**** BEGIN LOGGING AT Sun Aug 17 02:59:59 2014 Aug 17 04:34:26 Does anyone know where I could get the BeagleBone Black schematic and PCB files, but for EagleCAD instead of OrCAD? Aug 17 04:35:16 ahahahaahaha Aug 17 04:35:51 Yes? Aug 17 06:01:41 twocubed: in an alternative universe. that's what veremit was trying to say. Aug 17 09:12:09 my bbb came yesterday. i love it so much already. this is so much better than an arduinomega connected to a pi Aug 17 09:13:09 and i did not even get to try the processing power yet :D Aug 17 09:14:31 and i still can hook up the mega to get even more pins :D Aug 17 18:51:21 Is it possible to load automaticly custom cape firmware by putting it in the uEnv.txt? Aug 17 18:51:42 I take an error on my BBB running archlinux Aug 17 18:51:56 [ 60.751762] bone-capemgr bone_capemgr.9: failed to load firmware 'BB-DCAN1-00A0.dtbo' Aug 17 19:04:54 how is sitara (am335x) related to OMAP? Aug 17 19:05:10 ie why do omap related features are enabled in kernel config? Aug 17 19:05:24 my understanding is that they are different processors Aug 17 19:17:18 sigchild: I believe that omap were also in the sitara grouping of processors, they're both cortex a8 implementations Aug 17 19:17:32 but yes they are different processors Aug 17 19:19:04 sigchild: probably to increase the chance to run this kernel on omap boards Aug 17 19:22:02 hm... i found a post with a similar question in TI forums. Someone from TI said that Sitara share a lot of IP. Aug 17 19:23:26 http://e2e.ti.com/support/arm/sitara_arm/f/791/t/235682.aspx Aug 18 00:43:44 bborg_builds: commands Aug 18 00:43:44 buildbot commands: commands, dance, destroy, excited, force, hello, help, last, list, mute, notify, source, status, stop, unmute, version, watch Aug 18 00:43:53 bborg_builds: notify Aug 18 00:43:53 try 'notify on|off|list ' Aug 18 00:44:04 bborg_builds: notify on started Aug 18 00:44:04 The following events are being notified: ['started'] Aug 18 00:44:11 bborg_builds: notify on finished Aug 18 00:44:11 The following events are being notified: ['started', 'finished'] Aug 18 00:44:14 bborg_builds: notify on failure Aug 18 00:44:14 The following events are being notified: ['started', 'failure', 'finished'] Aug 18 00:46:50 bborg_builds: notify list Aug 18 00:46:51 The following events are being notified: ['started', 'failure', 'finished'] Aug 18 00:47:02 bborg_builds: dance Aug 18 00:47:03 <(^.^<) Aug 18 00:47:04 <(^.^)> Aug 18 00:47:06 (>^.^)> Aug 18 00:47:06 (7^.^)7 Aug 18 00:47:08 (>^.^<) Aug 18 00:47:25 bborg_builds: excited Aug 18 00:47:25 What you say! Aug 18 00:48:02 build #0 of runtests started, including [] Aug 18 00:48:02 build #0 of runtests is complete: Failure [failed git] Build details are at http://localhost:8010/builders/runtests/builds/0 Aug 18 00:49:56 build #1 of runtests started, including [] Aug 18 00:49:56 build #1 of runtests is complete: Failure [failed git] Build details are at http://builds.beagleboard.orgbuilders/runtests/builds/1 Aug 18 00:50:27 build #2 of runtests started, including [] Aug 18 00:50:27 build #2 of runtests is complete: Failure [failed git] Build details are at http://builds.beagleboard.org/builders/runtests/builds/2 Aug 18 00:53:03 hmmm... not sure why it is trying to fetch the master branch Aug 18 00:53:12 build #3 of runtests started, including [] Aug 18 01:19:12 bborg_builds: source Aug 18 01:19:12 My source can be found at http://buildbot.net/ Aug 18 01:19:21 bborg_builds: status Aug 18 01:19:21 runtests: building('make -j4 ...') Aug 18 01:19:45 bborg_builds: watch Aug 18 01:19:45 try 'watch ' Aug 18 01:19:52 bborg_builds: watch runtests Aug 18 01:19:52 watching build runtests #3 until it finishes.. Aug 18 01:34:12 build #3 of runtests is complete: Success [build successful] Build details are at http://builds.beagleboard.org/builders/runtests/builds/3 Aug 18 01:49:33 Hi guys, I've asked a few times, but I'm still a bit hesitant, and a few people didn't quite understand what I was asking. Aug 18 01:50:16 I bought a usb hub, it came with a 5v 3A power supply. I wanted to Y the power cable, to power the hub and the BBB, but was worried about having the BBB powered usb (host) going into a powered usb hub from the same adapter. http://i.imgur.com/G4OimXb.jpg is the cable I made Aug 18 01:50:48 I've tested it individually, and connecting both the hub and the bbb concurrently, but not with the cable from the BBB to the HUB.. I'd really hate to fry something.. but it should be okay? Aug 18 01:54:16 tawr: Yes. Aug 18 01:54:39 agmlego, okay as in it should be fine? Aug 18 01:56:45 Yes. Aug 18 01:57:20 If you are really, really worried about it, put a Schottky diode in line with the positive line coing out of the bone. Aug 18 02:00:43 I was debating even removing the power wires from the bbb to the hub since I'm going to make a custom shorty cable Aug 18 02:01:19 i'm planning on making my bbb nearly a 'laptop' inside a pelican mil-spec case Aug 18 02:02:11 http://i.imgur.com/RteTuCP.jpg is the upper plate/mount, where the ports and monitor will be placed. a lower level will have the bbb, the lipo pack, dc-dc converter, charging circuits, etc **** ENDING LOGGING AT Mon Aug 18 02:59:59 2014