**** BEGIN LOGGING AT Wed Feb 24 02:59:58 2016 Feb 24 10:12:16 hi Feb 24 10:19:11 moin :) Feb 24 19:53:11 hmm, mrawviewer segfaults in strlen called from g_strconcat ... lovely. Feb 24 19:53:29 does anyone use it? Feb 24 19:54:48 even more funny ... libraw-lite installs archive libs (.a) only, which means that mrawviewer should be statically linked against it ... Feb 24 19:54:56 but mrawviewer still depends on libraw-lite. Feb 24 20:30:09 what's mrawviewer? Feb 24 20:30:45 bencoh: what if it embeds a linker Feb 24 20:38:51 kerio: "lol" Feb 24 20:38:55 DocScrutinizer51: a RAW viewer Feb 24 20:38:58 based on libraw Feb 24 20:39:19 (RAW images, like DNG) Feb 24 21:18:58 What should camera's video-recording do when a phone call comes in? Ideally, it would pause itself, and after-call user would have options to either continue video recording or stop it? Feb 24 21:21:01 Because for me, camera's video recording just broke, fairly strongly. Had to reboot entire device Feb 24 22:58:33 It'd be nice to have camera-ui record in something other than the MPEG4 container. Feb 24 22:59:32 That stores some metadata at the end of the file, so if something crashes you lose everything unless you can be bothered hacking the information back into the file. Feb 24 23:04:02 how do I remove the microSD board thing? Feb 24 23:16:07 ugh Feb 24 23:16:14 these USB pins look impossibly small Feb 24 23:16:30 is it reasonable to just line them up and glue the thing down? :/ Feb 24 23:26:48 help :< Feb 24 23:31:34 Broken microUSB charging port? Feb 24 23:33:44 Oksana: yes Feb 24 23:37:24 Hopefully, somebody helps. I haven't ever tried to repair it, I am going to, but I am wary and procrastinating Feb 24 23:42:01 it looks hopeless Feb 24 23:42:14 tiny pins and no way to access thm Feb 24 23:53:35 ~usbfix Feb 24 23:53:36 hmm... usbfix is http://talk.maemo.org/showthread.php?t=75920 - and **NEVER** use epoxy (unless you want to seal your device for underwater), or https://www.youtube.com/watch?v=fYz5nIHH0iY#t=1866, you will basically need two irons: a small good one (or better hot-air reflow) and a 60+ Watt Feb 24 23:54:01 Luke-Jr: IMO, if you can get a hot air station, or a heatgun with a small-tip adapter and kapton tape, go with that! Feb 24 23:54:23 I have a hot air thing Feb 24 23:54:58 Apply kapton tape to mask off the board around the port, drown it in rework/no-clean flux, and heat it up Feb 24 23:55:29 I have no clue what that means ._. Feb 24 23:57:21 Luke-Jr: Kapton tape's basically heatproof, you want to use it to protect the passives and traces to avoid damage to them Feb 25 00:01:34 oh well, I probably don't have any and wouldn't know where to put it even if I did Feb 25 00:01:41 and I have to travel in ~2 days Feb 25 00:18:56 http://maemo.cloud-7.de/share-service/20160225_001.jpg Feb 25 00:25:24 DocScrutinizer51: how to fix USB? :x Feb 25 00:32:04 ~usbfix Feb 25 00:32:06 i heard usbfix is http://talk.maemo.org/showthread.php?t=75920 - and **NEVER** use epoxy (unless you want to seal your device for underwater), or https://www.youtube.com/watch?v=fYz5nIHH0iY#t=1866, you will basically need two irons: a small good one (or better hot-air reflow) and a 60+ Watt Feb 25 00:44:01 DocScrutinizer51: read all that, nobody says how to actually do it Feb 25 00:51:02 Luke-Jr: make photos Feb 25 00:57:20 but actually there are howtos to fix USB Feb 25 01:15:09 DocScrutinizer51: my camera is in pieces ;) Feb 25 01:15:16 * Luke-Jr wonders if hot glue would work Feb 25 01:33:39 DocScrutinizer51: http://luke.dashjr.org/tmp/photo/20160224_202257.jpg Feb 25 01:35:57 DocScrutinizer51: http://luke.dashjr.org/tmp/photo/20160224_202305.jpg Feb 25 01:59:33 the problem is if the pads on the pcb got ripped off, which likely they will be... can you tell? Feb 25 02:06:09 ecc3g: it doesn't look like they did, does it? :/ Feb 25 02:06:53 my problem is it seems impossible to get to the pads if the port is placed, and even trying to solder the sides down fails because the solder globs to the top of the port away from the PCB Feb 25 02:07:06 and even when I get it on the pcb, it breaks off immediately again Feb 25 02:08:05 annoyingly, spare N900 won't charge the battery apparently either Feb 25 02:08:12 unplug and it dies immediately Feb 25 02:13:33 if it breaks off immediately, the pads aren't there... got lots of flux? Feb 25 02:14:08 and yes you need a very thin solder iron tip... Feb 25 02:14:19 there never were pads where I am trying to solder it down on the sides Feb 25 02:14:37 if my solder iron tip was any thinner, it'd break Feb 25 02:15:06 there is no place to put a solder iron near the pads Feb 25 02:15:16 so I figure I just need to line them up and hope for the best there Feb 25 02:18:22 probably need a hot air rework or make a really thin "tip" with a paperclip...but I doubt this will conduct heat fast enough to solder. Feb 25 02:18:55 I have nowhere to fit a paperclip Feb 25 02:19:09 there's a big metal shield immediately behind the USB port Feb 25 02:19:31 I can do hot air, but no clue how to handle that around the rest of the PCB Feb 25 02:19:46 would probably melt the microSD cable Feb 25 02:23:17 Luke-Jr: to solder down the USB pinds tou usually need to remove some of the USB jack steek 'roof' Feb 25 02:23:59 DocScrutinizer51: how? :| Feb 25 02:24:14 or you use solderpaste, flux, and hot air Feb 25 02:24:37 how? Dremel Feb 25 02:25:05 what temp hot air won't destroy crap? Feb 25 02:25:31 not that I have or know what solderpaste is :x Feb 25 02:25:35 260 Feb 25 02:25:58 hmm Feb 25 02:26:20 google for solderpaste Feb 25 02:27:19 hm, retired SparkFun product Feb 25 02:27:22 same as wire glue? Feb 25 02:27:35 I should have that somewhere although I couldn't find it when I looked earlier Feb 25 02:27:47 it's solder balls in flux gel Feb 25 02:29:07 is there a chance I'll get anywhere if I just place the port and heatgun it? Feb 25 02:29:26 solderpase is usd to build *every* reflow-soldered device Feb 25 02:30:18 yes _ use good solderwire and lots of excellent flux Feb 25 02:31:04 no-clean SMT flux Feb 25 02:31:19 am I likely to find that local anywhere? Feb 25 02:31:39 hardly Feb 25 02:32:30 sorry I'm roaming so no good bookmarked links Feb 25 02:47:19 conrad, some blabla58? flus pen Feb 25 02:48:12 SMT flussmittrl stift **** ENDING LOGGING AT Thu Feb 25 02:59:59 2016