**** BEGIN LOGGING AT Sat Mar 15 02:59:56 2008 Mar 15 03:26:04 Hello Mar 15 04:37:46 hello... total newbie here fishing for HW guidance; am I in the right place? Mar 15 04:43:32 Sure. Mar 15 04:43:55 But have patience while waiting for answers. Lots of idlers here. Mar 15 04:44:06 great, thanks. Mar 15 04:44:54 so, i bought a NSLU2 off ebay. I have it on a crossover cable connected to my debian linux box. i power the slug on, after some time it gets a DHCP lease, and I can pull up the linksys webpage from it. so far so good. Mar 15 04:45:11 but I've not been able to get it into upgrade mode, or telnet into the bootloader. Mar 15 04:45:23 (despite VERY CAREFULLY following the instructions on the wiki :) Mar 15 04:45:57 Use the reset button method, always works. Mar 15 04:46:29 ok. should ethernet be plugged or unplugged? should i disconnect power when I power-down, or just use the power button? Mar 15 04:48:19 Leave the ethernet plugged in. Unplug all USB devices. Pull the power plug. Put power plug back, hold reset button depressed, push power button to power on -- you'll see a color change in the power LED (may be very subtle indeed) about 10 - 15 seconds after power up -- immediately release the reset button. Mar 15 04:48:45 The power LED will blink green/red to signal that you are in upgrade mode. Use upslug2 on the debian box to upload your new firmware. Mar 15 04:49:53 ah, it's the power led? the wiki says ready/status LED Mar 15 04:50:24 Er, sorry. yes, it's the ready/status. Mar 15 04:51:01 ok. when i hold reset and press power, none of the 4 top leds (including ready/status) comes on Mar 15 04:51:11 (previously, i did see the ethernet led come on, but never the ready/status) Mar 15 04:52:45 Really? That's not good. Mar 15 04:52:50 I tried arping the box on 192.168.0.1 while booting, and it never responds Mar 15 04:53:12 is it time to go to serial? or jtag? Mar 15 04:53:37 Serial would be helpful. JTAG is a really last resort. Mar 15 04:53:48 You got it from where? Mar 15 04:53:54 ebay... Mar 15 04:54:13 Any mods done by the previous owner? Mar 15 04:54:29 he claims no, the box looks pristine, and like i said, it came on just fine with the linksys firmware Mar 15 04:55:42 Ok. Very odd. But lets just make sure we've got the right procedure - plugged in, power is off, the little reset button inside the hole at the back is depressed, then you push the power button -- and you get no LED activity at all? Mar 15 04:55:55 the power light does go green. Mar 15 04:55:59 the four on top stay dark Mar 15 04:57:19 But the leds work normally when it boots up into the Linksys firmware? Mar 15 04:57:25 actually, i take it back, it was "amazon marketplace", not ebay. Mar 15 04:57:48 the ethernet and status light seem to behave normally. i haven't tried plugging in any disks so don't know about disk1, disk2 Mar 15 04:58:03 although the bootup does seem to be quite slow. 5 minutes sometimes. Mar 15 05:00:16 actually now it doesn't want to boot at all. worked before though. Mar 15 05:00:59 it did beep a few times when it booted, is that normal? Mar 15 05:01:05 You might like to check the power supply. They are not of the, um, highest quality, shall we say? Mar 15 05:01:13 aha, good call Mar 15 05:09:46 you're right, it's quite flaky Mar 15 05:10:00 but i am able to get into reboot after unplugging and plugging it again. so thanks! Mar 15 05:10:05 *redboot Mar 15 05:10:44 :) Well, the good news is that the PSU is relatively easy to replace. Mar 15 05:10:55 Enjoy! Mar 15 05:11:02 yeah, probably will not be using it anyway, my planned installation has 5VDC already available. Mar 15 05:11:14 Enough current as well? Mar 15 05:11:27 wiki suggested around half an amp, that should be no problem Mar 15 05:11:46 That'll do for the unit itself, USB devices would be in addition of course. Mar 15 05:11:59 true, was planning to use i2c though :) Mar 15 05:12:20 Ah, ok. So mods are in order. Mar 15 05:12:37 What firmware do you have in mind? Mar 15 05:12:51 indeed. i have about 1/2 a mind to make myself a usb client device just for fun, but i2c seems so much easier Mar 15 05:13:03 i picked openSlugBE pretty much at random Mar 15 05:13:24 hmmm... pretty reasonable choice. Mar 15 05:13:26 i want to run a simple web service and ssh daemon, and collect some data over i2c Mar 15 05:13:36 hoping not to have a thumb drive, but can supply one if needed. Mar 15 05:14:37 ssh is built in, you might be able to stuff a very small httpd on it as well, but if you really want not to have a thumb drive, you might end up with OpenWRT on it. Mar 15 05:15:05 But SlugOS is a find place to start with - lots of other users, which helps. Mar 15 05:15:13 yeah, i've messed with openWRT on my WRT, was hoping for something a little nicer Mar 15 05:15:53 I'd recommend a serial port while you have it open and the soldering iron warmed up. Mar 15 05:16:00 yeah, sounds prudent Mar 15 05:22:23 hooray, I'm logged in as root! Mar 15 05:35:45 is lighttpd a good starting package? Mar 15 12:27:28 hey Reedy_Boy Mar 15 12:27:39 'lo Mar 15 12:27:51 what versoin of rtorrent and its libs are you using ? Mar 15 12:27:58 you're running debian/slug, right ? Mar 15 12:28:09 yeah Mar 15 12:28:11 custom built IPKG verson Mar 15 12:28:13 moment Mar 15 12:28:22 http://ipkg.reedyboy.net/optware-arm-etch/ Mar 15 12:28:27 Thats it and all its dependancies Mar 15 12:28:59 and xmlrpc works, right? Mar 15 12:29:10 ya Mar 15 12:29:18 wierd Mar 15 12:29:28 waht is? Mar 15 12:29:37 brb, need to check on the malt loaf in the oven Mar 15 12:29:57 its xmlrpc 1.11.00-2 libtorrent 0.11.9+r1 and rtorrent 0.7.9+r1027 Mar 15 12:30:00 oh. Mar 15 12:30:02 hrm Mar 15 12:30:23 http://www.mediamax.com/bzhou/Hosted/optware/cs04q3armel -> is this yours too ? Mar 15 12:31:12 ugh. gotta go eat with family, so brb in 15-20 Mar 15 12:31:29 if you can get your versoins built for slugOSLE i'd really love that Mar 15 12:31:37 nope, thats eno's repos Mar 15 12:31:44 but should be the same version, we did them about the same time Mar 15 12:31:48 i think he said he had xmlrpc working too Mar 15 12:31:52 ya Mar 15 12:32:04 they were from the same sources built in the same way Mar 15 12:32:08 but thats weird since the slugOSLE has just about the sameversions Mar 15 12:32:16 * Reedy_Boy shrugs Mar 15 12:32:19 i dont really know Mar 15 12:32:25 no, his versions are newer then yours Mar 15 12:32:35 he *may* have updated them Mar 15 12:32:45 hrtm. Mar 15 12:32:56 you don't know what ? Mar 15 12:33:47 sorry? Mar 15 12:34:01 your said '< Reedy_Boy> i dont really know' Mar 15 12:34:11 but thats weird since the slugOSLE has just about the sameversions Mar 15 12:34:15 related to that Mar 15 12:35:08 hrm Mar 15 12:35:17 anywho, can oyu build your versions for slugOSLE ? Mar 15 12:35:48 brb Mar 15 12:35:48 I cannot reach my 2 slugs. telnet, ping works, a server works. not webconfig not shares. tried from 2 PC:s. worked perfect yesterday. grmbl...some have a idea what to check? Mar 15 12:37:25 restarted them? Mar 15 12:37:32 ido-, possibly... via a similar method i suspect Mar 15 12:38:21 tried with connect one of them direct to router.no change Mar 15 13:01:02 hey Mar 15 13:01:04 back. Mar 15 13:02:55 'lo Mar 15 13:03:22 well. Mar 15 13:03:32 can you build'em ? Mar 15 13:04:22 setting up a build env. is too complicatred for me.. Mar 15 13:56:27 I have just set my slug into upgrade mode, but upslug2 can't detect the device. What IP address is the slug set to in this mode? Mar 15 13:57:05 none Mar 15 13:57:43 What do I need to set my IP address of my computer to get thi to eork? Mar 15 13:57:50 *this to work Mar 15 13:58:40 I don't think you have to set it to anything; just have the nslu2 on the same switch or physical LAN segment. The protocol Linksys uses is beneath the TCP/IP layer IIRC. Mar 15 13:59:24 When I run the program, I get this error: eth0: Device not configured: error using device [BIOCSETIF: eth0: Device not configured] Mar 15 13:59:41 Are you running it as root? Mar 15 13:59:45 Yes Mar 15 14:00:00 [yauMac:~/Public/Today/upslug2-11] root# ./upslug2 Mar 15 14:00:32 Ok, then you probably have to at least bring up eth0 -- so give it some IP address: "ifconfig eth0 192.168.0.222" or similar Mar 15 14:01:04 Oops Mar 15 14:01:15 I have en0 not eth0 Mar 15 14:02:06 Oh, well that's a problem then. :D Mar 15 14:02:36 upslug2 -d en0 Mar 15 14:02:52 Sweet... my bad Mar 15 14:02:58 cheers Mar 15 14:24:33 rintintin Mar 15 14:27:21 hi. anyone around here running slugos? :) Mar 15 14:27:47 me me me Mar 15 14:28:04 im thinking about switching from debian to slugos Mar 15 14:28:22 okay.. and ? Mar 15 14:28:25 why ? Mar 15 14:28:37 is there any space left on the internal flash after you install slugos? Mar 15 14:28:41 mainly for fun ;) Mar 15 14:28:48 oh i dont remember Mar 15 14:28:56 i use an external disk anyhow Mar 15 14:29:13 no rtorrent with xmlrpc though Mar 15 14:29:18 okay. im going to run rtorrent and lighttpd Mar 15 14:29:20 unless someone builds it correctly Mar 15 14:29:23 :< Mar 15 14:29:30 and you're welcome to do it Mar 15 14:29:35 for fun Mar 15 14:29:42 dont need xmlrpc. i need rtorrent though Mar 15 14:29:46 actually i'd b grateful. Mar 15 14:29:50 so it works Mar 15 14:30:18 do you think rtorrent and lighttpd can fit on the internal flash? Mar 15 14:30:24 i'm notsure Mar 15 14:30:32 but where would you download rtorrent to ? Mar 15 14:30:47 i have an external drive for the downloads Mar 15 14:31:18 so you put rtorrent on that.. Mar 15 14:31:22 but i whould like to have all software on the internal flash, if possible. so i could remove the drive without shutting the system of Mar 15 14:31:30 i guess i could :) Mar 15 14:31:30 oh, i see. Mar 15 14:31:57 /dev/mtdblock4 6.4M 4.8M 1.6M 75% /initrd Mar 15 14:32:12 1,6mb free? Mar 15 14:32:13 nothing installed there apart from the basic stufffrom firmware Mar 15 14:32:18 seems so. Mar 15 14:32:37 /dev/sdb1 698.5G 49.7G 648.8G 7% /media/sdb1 Mar 15 14:32:42 thanks for the info. have no idea how much space rtorrent takes up though :) Mar 15 14:32:46 thats not on the slug though. Mar 15 14:33:25 get the libtorrent and rtorrent packages to find out Mar 15 14:33:27 from optware Mar 15 14:35:11 is there any webpage where i can browse around and find info on the packages? Mar 15 14:35:22 sure Mar 15 14:36:08 http://ipkg.nslu2-linux.org/feeds/optware/slugosle/cross/unstable Mar 15 14:36:35 this is the thtst the feed Mar 15 14:37:30 okay. the package takes 417k for rtorrent and 348k for libtorrent Mar 15 14:37:40 i dont think i can fit lighttpd in there too ;) Mar 15 14:38:07 are those packages compressed? Mar 15 18:50:43 hi@all Mar 15 20:10:08 how can i add graphics in the wiki? Mar 15 20:23:33 send an email with the url to the graphic or image to the mailing list, and request that it be made availalbe to be linked to in the wiki. Mar 15 20:29:05 it is a wiki with a few pic's Mar 15 20:29:26 how can i place them in order as i need? Mar 15 20:29:40 uploadspace is no problem Mar 15 21:06:59 ho is the menu in win explorer named where you can mount network drives? (in german it's "Extras") Mar 15 21:10:51 Tools Mar 15 21:10:53 IIRC Mar 15 21:10:55 on XP Mar 15 21:11:04 ok Mar 15 21:11:06 thx Mar 15 21:11:21 and the "mount network drives" ? Mar 15 21:12:25 yup Mar 15 21:12:32 fine :) Mar 15 21:12:49 i hope, anybody understand the howto :) Mar 15 21:13:26 it's hard for me to write it in englisch caus i've learnd it over 25 years aggo Mar 15 21:14:05 maybe anybody can correct it :) Mar 15 21:19:18 Yeah, if you post a link, i'll read over it :) Mar 15 21:19:26 oh yeah my /etc/init.d/beep is sweet :) Mar 15 21:20:43 xD Mar 15 21:27:50 http://www.cs-seniorenheim.de/nfs_windows_howto Mar 15 21:28:00 here we go again :) Mar 15 21:28:20 pic's are not included yet Mar 15 21:43:41 how is it? Mar 15 21:46:24 I read it I think I understadn it=). but i dont know what is neededto at the nslu2 Mar 15 21:47:03 only a nfs server Mar 15 21:47:24 small wrong spelling erorrs Mar 15 21:47:54 your local Mashine "machine" Mar 15 21:48:24 and copyed think its copied Mar 15 21:48:25 =) Mar 15 21:49:10 is screenshots included later? Mar 15 21:50:08 yes, but not much later. :) Mar 15 21:50:16 mashine changed Mar 15 21:50:21 to computer :) Mar 15 21:50:57 under "pic8" allreadi already Mar 15 21:52:26 done Mar 15 21:52:29 under pic23 chose -->choose Mar 15 21:53:47 done Mar 15 21:53:57 finaly under pic 28 expoted --exposed (?) Mar 15 21:54:30 Klick -> Click Mar 15 21:54:34 done too :) Mar 15 21:54:40 of your mounted folder instead? Mar 15 21:54:45 more clear Mar 15 21:55:30 done :) Mar 15 21:56:21 need a cig after all that hard work=) Mar 15 21:56:37 hihi Mar 15 22:14:13 oh, about six and a half hour to upload my files to the nslu via nfs Mar 15 22:14:47 roundabout 100GB :) Mar 15 22:18:20 many many good torrent downloads then=) Mar 15 22:19:29 no, series recorded from TV :) Mar 15 22:20:07 mediatomb and ushare freeze the nlsu2when share goes over 50 Gb or so:( dont no if its the same on slugos ...I got unslung Mar 15 22:20:54 mediatomb? ushare? Mar 15 22:21:48 its applications to use on the nslu2 if you have a mediaplayer. I use one of my nslu2 for that Mar 15 22:23:59 i use the nslu only for share. Mar 15 22:24:11 for server jobs i use this http://www.saintsong.com.tw/english/gx1.htm Mar 15 22:24:55 it has only USB1.1, so i decided to attach the drives via the slug in my network Mar 15 22:26:49 interesting Mar 15 22:28:09 what is the proce for it? Mar 15 22:28:12 *price Mar 15 22:55:53 i've bought it from a friend. it's about three years old Mar 15 22:56:11 look at ebay Mar 15 23:03:59 new it costs about 500$ with 40GB hdd and 256MB ram Mar 15 23:04:17 and a DVD-RW Mar 15 23:04:31 http://www.cappuccinopc.com Mar 15 23:12:08 I have one of the original cappuccino pc's. Started with a 6xxMhz Celeron with 128MB ram. Now has a P3 1.1G and 256MB ram. Makes a decent little process server but its expansion is far too limited. (I've been thinking of ripping out the CD drive and crafting an adapter to let me use a 3.5" drive in the bay. Mar 15 23:13:03 3.5" floppy drive? :) Mar 15 23:13:25 3.5" hard drive. Mar 15 23:14:06 what for? Mar 15 23:15:19 It is 4x (or more) times faster than a slug and uses 13w (whereas my slug uses 3). Mar 15 23:15:30 I'm a geek, do I need a reason? Mar 15 23:15:44 * joshin confiscates asa's geek card. Mar 15 23:15:59 :) Mar 15 23:18:17 I removed those annoyingly loud and worthless fans and bolted a 60mm fan to the top (at +7v). It is ugly but silent. Mar 15 23:19:02 (Red to +12, black to +5v) Mar 15 23:20:48 hi Mar 15 23:20:59 my cappuccino lies on the garret Mar 15 23:21:24 (or it's IN the garret) Mar 15 23:21:30 hey rexthedog Mar 15 23:21:32 i still have an old nslu2 here and am wondering if it will be capable of running a webserver that runs simple perl/cgi scripts (with unslug firmware) ? Mar 15 23:21:38 si it doesn't matter if it's louder Mar 15 23:22:04 rexthedog: It should be capable of it. But my slugs run SlugOS or Gentoo Mar 15 23:22:24 i dont want to install anything complicated Mar 15 23:22:32 i remember installing debianslug on it and it was a pain Mar 15 23:22:35 well not a pain Mar 15 23:22:41 but it took me more than 20 minutes Mar 15 23:23:08 Isn't apache in the unslung repository? Mar 15 23:23:30 IIRC Mar 15 23:24:04 but there are lighter weight servers Mar 15 23:24:23 hello Mar 15 23:24:45 i tryed all this evening to make work my nslu2, but i still can't connect it Mar 15 23:25:11 i flashed it twice with slugOS, it seems working, but no connectivity Mar 15 23:25:44 i tryed to ping at 192.168.1.77, i tryed to give a static adress from it mac adress, but no result Mar 15 23:26:01 i can't ping it, i can't ssh it. Mar 15 23:26:10 what IP was before flashing? Mar 15 23:26:23 192.168.1.77 Mar 15 23:26:28 hm Mar 15 23:26:51 PPmarcel: have you reflashed it? Mar 15 23:26:57 yes, twice Mar 15 23:27:03 slug OS both Mar 15 23:27:31 Ok, try flashing the Linksys firmware, booting that up, then follow any of the linksys procedures to reset to the factory defaults. Then reflash SlugOS once again. Mar 15 23:27:32 upslug and sercomm didn't give me any error after flashing Mar 15 23:27:38 ok Mar 15 23:27:52 Does it give the three beeps when it boots after flashing? Mar 15 23:27:59 no, on Mar 15 23:28:00 one Mar 15 23:28:10 Ok, then it does not finish the boot. Mar 15 23:29:10 i had already a problem when i upgraded it from debian to unslung Mar 15 23:29:15 samba couldn't work Mar 15 23:29:15 Try resetting to factory defaults, and see if that resolves the issue; that's the only thing left in the firmware when you reflash that could cause such a problem. Mar 15 23:29:44 use NFS instead of samba :) Mar 15 23:29:49 hehe Mar 15 23:29:58 hoto is written Mar 15 23:30:00 btw, it was a sign of prblem Mar 15 23:31:30 is there an howto for the wiki? i don't know how to format text. Mar 15 23:32:05 ^^ Mar 15 23:32:30 it's my first wiki text :) Mar 15 23:32:32 take a wiki with a lot of things, see how it is writing Mar 15 23:32:47 aha Mar 15 23:33:29 http://en.wikipedia.org/wiki/Wikipedia:How_to_edit_a_page Mar 15 23:33:40 is it tha same wiki? i don't know Mar 15 23:34:16 whats the nslu2 ip address when i want to use the telnet into redboot method? Mar 15 23:35:49 rexthedog: you shouldn't have to telnet into redboot anymore. Mar 15 23:36:36 mwester: factory reboot, i have it by pushing reset 20s? Mar 15 23:37:07 That should do it if that is what the Linksys documents say to do. Mar 15 23:38:00 i prefer reflash it Mar 15 23:38:28 hey i have following problem Mar 15 23:39:11 why the preview in the wiki don't work? Mar 15 23:39:20 is it my fault? Mar 15 23:39:32 i want to reflash my nslu2 with unslung, currently it is flashed with an old debianslug but i dont have the according usb-stick any more. can i still boot the nslu2 and will it get an ip so i can search for it with the sercomm utility? Mar 15 23:39:33 asa: the preview is broken Mar 15 23:39:52 oh :( Mar 15 23:40:14 rexthedog: Use the reset-button technique to enter upgrade mode. Upgrade mode does not use an IP address at all. Mar 15 23:40:39 is it possible to edit the wiki ewery time i want? Mar 15 23:40:51 yes Mar 15 23:41:18 mwester: where can i find something about the ugprade mode? Mar 15 23:41:31 never heard about it... Mar 15 23:42:14 the wiki: http://www.nslu2-linux.org/wiki/HowTo/UseTheResetButtonToEnterUpgradeMode Mar 15 23:42:49 ok, then i learn by trying :) Mar 15 23:43:36 Sure, just save it -- you can edit it as often as you need to make it right. No problem. Mar 15 23:44:02 ok and i can have my nslu2 just connected to my router like always? Mar 15 23:44:14 rexthedog: yes Mar 15 23:44:31 as long as it is in the same network, it's ok Mar 15 23:44:32 Yep. Just don't do it over wireless. Mar 15 23:44:47 (never reflash *anything* over wireless!) Mar 15 23:50:15 hey guys Mar 15 23:50:20 i have a problem with samba Mar 15 23:50:21 i think Mar 15 23:50:30 when transferring files from the pc to the slug Mar 15 23:50:46 once in a while (maybe 10 minutes or so) i get a 'disconnect' Mar 15 23:50:51 no reboot or anything Mar 15 23:50:57 when reconnecting to the share it works Mar 15 23:51:21 but i dont know why the connections drop in the middle of transferring files.. Mar 15 23:53:24 ido-: What firmware, and is anything printed into the /var/log/messages file or in dmesg when this happens? Mar 15 23:54:47 hov can i add a CR in the wiki? Mar 15 23:55:03 space space space? Mar 15 23:55:22 you can list sentences with * Mar 16 00:04:24 is there no easy way to insert pic's? Mar 16 00:04:28 oh Mar 16 00:04:31 i forgotto say mwester Mar 16 00:04:36 its slugosle Mar 16 00:04:44 something like image url in html? Mar 16 00:05:02 nothing in logmessages Mar 16 00:05:12 nor indmesg Mar 16 00:05:17 asa: http://wiki.splitbrain.org/wiki:syntax Mar 16 00:05:25 that's easy here Mar 16 00:05:51 oh, fine. many thx :) Mar 16 00:05:59 that's what i need Mar 16 00:06:22 maybe you need to change the syntax, i see a lot of "dokuwiki" eveywhere Mar 16 00:07:18 nothing in the samba logs either Mar 16 00:11:16 hm Mar 16 00:11:26 it doesn't work for me :( Mar 16 00:11:52 it tels me something about "Approved Sites"" Mar 16 00:12:00 what does this mean? Mar 16 00:16:19 asa: you need to wait for admin approve thoose links Mar 16 00:17:04 just yell little here about it when page is finished Mar 16 00:17:47 its there else spammers destroy the wiki Mar 16 00:18:44 hey again Mar 16 00:18:57 where can i find a working download link for the sercomm utility? Mar 16 00:21:56 http://www.everbesthk.com/8-download/sercomm/firmware/all_router_utility.zip Mar 16 00:22:46 this one doesnt work for me Mar 16 00:22:53 windows doesnt want to install :( Mar 16 00:23:07 http://www.everbesthk.com/8-download/sercomm/firmware/NU54/Upgrade_207_XP.zip Mar 16 00:23:11 that? Mar 16 00:23:29 any admin here? :) Mar 16 00:23:35 same Mar 16 00:24:59 brb Mar 16 00:25:54 hm, it wouldn't save :( Mar 16 00:28:43 asa its needed admin approve links then it works. I had the same problems a few days ago. Mar 16 00:28:59 need patience=) Mar 16 00:29:17 hm Mar 16 00:30:02 page need some admin approve links: http://www.nslu2-linux.org/wiki/Info/NFSonVista Mar 16 01:02:01 asa, page approved Mar 16 01:03:04 oh Mar 16 01:03:07 thx Mar 16 01:03:26 but it don't show the pic. only the link. Mar 16 01:03:40 what have i done wrong? Mar 16 01:07:04 juhuuu Mar 16 01:08:46 it works :) Mar 16 01:11:06 great Mar 16 01:15:19 hmm Mar 16 01:15:39 if i just want to run a simple cgi script by http, what server do i use on unslung? apache or php-thttpd ? Mar 16 01:17:29 optware busybox comes with a httpd that support CGI Mar 16 01:17:55 thttpd too, apache seems overkill Mar 16 01:18:10 ok... Mar 16 01:18:32 lighttpd should also work Mar 16 01:18:52 there's also a minihttpd Mar 16 01:20:08 i guess best is to use the busybox one, huh ? Mar 16 01:20:29 eno: why is WindowsXP with e ? at the end? Mar 16 01:23:13 wiki treat this kind of word automatically as a internal link Mar 16 01:23:47 there's a way to suppress this Mar 16 01:27:10 [=SuppressWikiWord=] Mar 16 01:28:43 thx Mar 16 01:37:37 so, the HowTo for NFS on XP is finished Mar 16 01:37:56 how can i turn it from "Info" to "HowTo"? Mar 16 01:39:21 and change the title fom "NFSonVista" to "NFS on Windows XP and Vista" ? Mar 16 01:40:00 i guess it's copy to new page and delete the old page Mar 16 01:41:06 hmm Mar 16 01:43:02 sorry for so many questions, but its' my first wiki article Mar 16 01:43:22 how can i make a new page ? Mar 16 01:53:36 how can i make another script to start automatically when my unslung nslu2 boots? Mar 16 02:04:36 does anyone know why im getting "E: Failed to fetch http://ftp.uk.debian.org/debian/pool/main/a/apache2/apache2.2-common_2.2.3-4+etch3_arm.deb: 404 Not Found" when i try to install PHPx under Debian on the my nslu?? **** ENDING LOGGING AT Sun Mar 16 02:59:56 2008