**** BEGIN LOGGING AT Sun Jul 09 02:59:57 2006
Jul 09 08:45:04 <NAiL> rwhitby: the leds script in the firmware should do the buzzer as well. You don't need a separate beep util except for when running debian.
Jul 09 08:49:33 <rwhitby> aha
Jul 09 08:50:22 <NAiL> the buzzer works out-of-the-box with 3.10
Jul 09 08:50:34 <NAiL> (using the "old" jbowler script)
Jul 09 10:16:47 <CIA-5> 03rwhitby * r3559 10optware/trunk/Makefile: Demoted packages that fail to build native on ds101g
Jul 09 10:44:49 <CIA-5> 03rwhitby * r3560 10optware/trunk/Makefile: Demoted packages that fail to build native on ds101g
Jul 09 10:46:57 <CIA-5> 03rwhitby * r3561 10optware/trunk/Makefile: Demoted packages that fail to build native on ds101g
Jul 09 10:48:24 <CIA-5> 03rwhitby * r3562 10optware/trunk/Makefile: Demoted packages that fail to build native on ds101g
Jul 09 15:27:54 <punani> hi all, i got a question: my USB 160GB HD is ext3 and corrupted so icheck it with e2fsck -y /dev/sda1
Jul 09 15:28:26 <punani> halfway it is exited with errorcode e2fsck 1.38 (30-Jun-2005)
Jul 09 15:28:26 <punani> Pass 1: Checking inodes, blocks, and sizes
Jul 09 15:28:26 <punani> Pass 2: Checking directory structure
Jul 09 15:28:26 <punani> Killed
Jul 09 15:28:26 <punani> [1] + Killed                     e2fsck -p /dev/sda1
Jul 09 15:28:42 <punani> what do i do wrong?
Jul 09 15:29:50 <punani> sorry wrong channel spank you all! ;)
Jul 09 17:27:30 <jr--> is there any existing code that i could shamelessly copy to get leds working on fgs3? stock snapgear code accesses them using ledman and IXP425_EXP_BUS_CS2. they're not controlled by gpio's like existing /dev/leds interface code expects.
Jul 09 17:28:54 <jr--> i got i2c working and found sources for rtc. lm-sensors shows sensible values, i can control fan speed etc. rtc set saves year as 2000 instead of 2006 for some reason. reads work ok if i set it using stock firmware.
Jul 09 18:52:11 <dr_nick> hi
Jul 09 18:54:48 <dr_nick> wow, i just found some posts on the german nslu2-info.de forum about the old spindown problem. nothing worked for my cheap usb-only harddisk (yakumo something w/ WDC harddisk)
Jul 09 18:55:11 <dr_nick> sdparm instantly gives error messages, scsi-idle does nothing
Jul 09 18:56:42 <dr_nick> but now, using sg_start from sg3-utils debian package would instantly spin down that disk. i'm really amazed, because i didn't find anything about sg3-utils on the wiki
Jul 09 20:05:15 <jr--> ok. got another beginner question. fsg3 has two ethernets and mac addresses are stored on redboot config part of flash. i copied code from nslu2_setup and changing offset + dev_addr[5] i can either fix either eth0 mac of eth1 mac, but how do i fix them both?
Jul 09 21:08:22 <jr--> ok got mac address issue sorted out. however i do get "scheduling while atomic: ifconfig/0x00000001/930" when running ifconfig with more than one ethernet interfaces up. shutting either one of then down with ifconfig ethx down silences it.
Jul 09 21:57:21 <jr--> got rtc working too. there was typo on isl1208 driver posted to lkml.
Jul 10 01:28:29 <CIA-5> 03bzhou * r3563 10optware/trunk/make/py-sqlalchemy.mk: py-sqlalchemy: upstream upgrade to 0.2.5
**** ENDING LOGGING AT Mon Jul 10 02:59:56 2006