**** BEGIN LOGGING AT Sat Aug 12 02:59:56 2006 Aug 12 04:07:50 03bzhou * r3763 10optware/trunk/make/py-paste.mk: py-paste: upstream upgrade to 0.9.7 Aug 12 04:36:37 03bzhou * r3764 10optware/trunk/ (make/ncftp.mk sources/ncftp/configure2.patch): ncftp: upstream upgrade to 3.2.0 Aug 12 07:03:35 re * Aug 12 07:03:38 can i have serial cable w/ max232 ? Aug 12 07:03:42 i can't get max3232 3.3v here, :-( Aug 12 12:38:33 eFfeM, i got Siemens C25 cable :-) Aug 12 12:39:42 great, see the wiki on how to connect it Aug 12 12:40:12 what I did was carefully pry open the siemens end, and note the colors to the various pins in the connector Aug 12 12:40:28 you can find the pinout of the connector on the web Aug 12 12:40:44 that way you can easily find rx, tx etc Aug 12 12:41:20 kid just came home from holiday, I'm going to listen to his story, back later Aug 12 12:41:34 eFfeM, see u latter :-) Aug 12 13:36:29 03rwhitby * r3765 10optware/trunk/Makefile: Transcode fails to build on nudi for fsg3 Aug 12 13:46:39 03rwhitby * r3766 10optware/trunk/Makefile: amule and ficy fail to build on nudi for ddwrt Aug 12 13:57:05 03rwhitby * r3767 10optware/trunk/Makefile: elinks, procps, sdl, snownews, xcursor, xfixes, xft and xrender all fail to build on nudi for ddwrt Aug 12 16:27:58 03bzhou * r3768 10optware/trunk/make/less.mk: less: use ncursesw on platforms that it is available Aug 12 16:43:07 03bzhou * r3769 10optware/trunk/make/gnutls.mk: gnutls: upstream upgrade to 1.4.2 Aug 12 16:43:39 03bzhou * r3770 10optware/trunk/make/opencdk.mk: opencdk: upstream upgrade to 0.5.9 Aug 12 16:48:41 03bzhou * r3771 10optware/trunk/make/dcraw.mk: dcraw: upstream upgrade to 1.340 Aug 12 17:17:25 03bzhou * r3772 10optware/trunk/Makefile: dnsmasq broken for wl500g Aug 12 22:10:41 have now a working cross build of perl 5.8.8 for ds101g that generates it own perl for building on the host, based on the work of bzhou Aug 12 22:11:05 somebody there that would like to discuss about it? Aug 12 22:24:57 03gda * r3773 10optware/trunk/sources/perl/Cross/ (config.sh-powerpc-603e-linux perl.mk): perl: 5.8.8 cross, but not activated now Aug 12 22:26:31 03bzhou * r3774 10optware/trunk/make/py-sqlalchemy.mk: py-sqlalchemy: upstream upgrade to 0.2.7 Aug 12 22:27:41 03bzhou * r3775 10optware/trunk/make/py-pastescript.mk: py-pastescript: upstream upgrade to 0.9.7 Aug 12 22:28:39 03gda * r3776 10optware/trunk/sources/perl/Cross/Makefile: perl: 5.8.8 cross, but not activated now Aug 12 22:31:05 03gda * r3777 10optware/trunk/sources/perl/Cross/ (4 files): perl: 5.8.8 cross, but not activated now Aug 12 22:43:42 gda_, eno == bzhou, the only problem i'm aware of cross perl is how to make sure "perl '-V:install.*'" gets the same output of native built perl Aug 12 22:44:34 if that problem not solved, the current native build perl modules might not work with the new cross perl Aug 12 23:01:25 eno: okay, will look into that, but only for the ds101g of course, but if there is a problem it should by general Aug 12 23:01:54 eno: only one problem, there is no native build perl for the ds101g Aug 12 23:02:44 can somebody show me what a native build perl tells on a nslu2 with perl '-V:install.*'? Aug 12 23:09:30 eno: I get this lines: Aug 12 23:09:33 installarchlib='/opt/lib/perl5/5.8.8/ppc-linux'; Aug 12 23:09:47 installprivlib='/opt/lib/perl5/5.8.8'; Aug 12 23:09:58 installsitearch='/opt/lib/perl5/site_perl/5.8.8/ppc-linux'; Aug 12 23:10:08 installsitelib='/opt/lib/perl5/site_perl/5.8.8'; Aug 12 23:10:28 the other lines are not important Aug 12 23:10:40 this looks good for me Aug 12 23:13:25 eno: have to go sone, maybe you send me a mail if you think there is a problem? Aug 12 23:17:08 bye Aug 12 23:44:10 03rwhitby * r3778 10optware/trunk/Makefile: Demoted wxbase on oleg - failes to build on nudi Aug 13 00:13:31 03bzhou * r3779 10optware/trunk/ (Makefile make/netcat.mk): added netcat Aug 13 01:18:08 Uploading new ddwrt, oleg and fsg3 optware feeds now ... Aug 13 01:18:28 http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/unstable/ Aug 13 01:18:54 ditto for "oleg" (wl500gx with Oleg's firmware and updated uclibc libraries) and "fsg3" (Freecom FSG-3) Aug 13 01:45:16 rwhitby, this is really great Aug 13 01:54:56 oleo: I had to demote some uclibc packages to push the feeds through - we can work through the failures and see if any can be repromoted. Aug 13 02:32:35 eno-away: ping Aug 13 02:36:50 03rwhitby * r3780 10optware/trunk/make/buildroot.mk: buildroot: dirclean should not touch the toolchain dir - that's what the top-level toolclean target is for **** ENDING LOGGING AT Sun Aug 13 02:59:57 2006