**** BEGIN LOGGING AT Thu Feb 01 02:59:57 2007
Feb 01 09:21:53 <aproemel> vmaster: i've connected the Jtagkey tiny to my notebook, and installed everything, is it possible to debuf from notebook, when sending the programm from my workstation? i only want to take a view at my memory and to my register
Feb 01 09:34:46 <vmaster> aproemel: not sure what you mean
Feb 01 09:35:57 <aproemel> JtagDebugger: Laptop (only to take a look at the registers and memory areas) Codeupload: Workstation
Feb 01 09:36:22 <aproemel> Because USB cable to short, to connect my board to my workstation ^^
Feb 01 09:38:23 <vmaster> ah, ok
Feb 01 09:38:25 <vmaster> yeah, sure
Feb 01 09:38:32 <vmaster> is your laptop running linux or windows?
Feb 01 09:40:52 <aproemel> windows
Feb 01 09:41:08 <aproemel> i'm using the amontec tools
Feb 01 09:41:40 <aproemel> i'm currently having tmimng and clock problems
Feb 01 09:42:08 <aproemel> and have to fix it first
Feb 01 09:45:17 <vmaster> ok, did you install the drivers for the device, and is it recognized by windows?
Feb 01 09:46:52 <aproemel> i've installed them, and the key is recognized
Feb 01 09:56:47 <vmaster> get the latest openocd binary from www.yagarto.de
Feb 01 10:01:28 <aproemel> ok
Feb 01 10:03:02 <vmaster> install, run with the .cfg i gave you yesterday
Feb 01 10:03:23 <aproemel> yes, i'll do so
Feb 01 10:03:30 <vmaster> i'd use the command line: openocd -f config.file -d (-d enables debug output)
Feb 01 10:03:50 <vmaster> after that you should be able to telnet to port 4444
Feb 01 10:04:06 <vmaster> if the daemon doesn't start up check the debug output
Feb 01 10:04:43 <aproemel> ok
Feb 01 10:18:36 <aproemel> vmaster: works with embeste board
Feb 01 10:18:40 <aproemel> :-)
Feb 01 10:18:46 <aproemel> thanks for your help :-)
Feb 01 10:53:14 <vmaster> aproemel: you're welcome
Feb 01 11:15:34 <nm_> hey vmaster
Feb 01 11:15:40 <nm_> are you there ?
Feb 01 11:41:19 <vmaster> hey nm_ 
Feb 01 11:41:43 <nm_> vmaster, have you ever used usb2sprite's Macr jtag ?
Feb 01 11:42:42 <vmaster> nm_: no. i contacted macraigor once regarding their raven device, but they basically told me that they're not interested in 3rd party software using their hardware
Feb 01 11:45:34 <nm_> vmaster, can our openocd work w/ usb2sprite ?
Feb 01 11:46:55 <vmaster> nm_: one would have to reverse-engineer their protocol
Feb 01 11:47:26 <nm_> vmaster, hmm i'm understand
Feb 01 11:47:57 <vmaster> nm_: and honstely i don't see why anyone would buy their $225 hardware that doesn't provide any advantage over a <$100 FT2232 based JTAG interface
Feb 01 11:48:34 <vmaster> the only argument for macraigor devices is their wide variety of supported hardware, where the OpenOCD only support ARM7/9, XScale and Cortex-M3
Feb 01 11:49:22 <nm_> vmaster, my device using IXP425, i will have deep testing w/ openocd 
Feb 01 11:49:48 <nm_> vmaster, i have search around on the internet, "someone" said that openocd worked w/ IXP425
Feb 01 11:50:15 <vmaster> i've read that, too, but I don't have contact with anyone personal
Feb 01 11:50:33 <vmaster> basically it should work, and if it doesn't, there shouldn't be any major issues to be solved
Feb 01 11:50:58 <vmaster> the most important thing is a useable reset
Feb 01 11:51:09 <vmaster> to debug an XScale, you need individual access to both reset lines
Feb 01 11:51:30 <vmaster> if the board uses a reset supervisor that's push-pull instead of open-drain you've got a problem
Feb 01 11:51:40 <vmaster> if the board connects both reset lines together, you have a problem
Feb 01 11:51:59 <nm_> vmaster, nice, i'll try it w/ my IXP425
Feb 01 14:12:02 <aproemel> vmaster: are you still there ?
Feb 01 14:21:09 <vmaster> aproemel: back again
Feb 01 14:21:32 <aproemel> wb
Feb 01 14:21:57 <aproemel> do you have an idee, why SDCS wont get more then 1 cycle low ?
Feb 01 14:23:26 <aproemel> on a write cycle
Feb 01 14:23:46 <aproemel> a read cycle is 6 cycles long
Feb 01 14:42:14 <vmaster> aproemel: not really - i doubt it's a configuration problem, as the chip select should never be low for such a short period
Feb 01 14:42:40 <aproemel> i think so too, and i'm currently checking my registers
Feb 01 14:47:54 <aproemel> quiet confusing
**** ENDING LOGGING AT Fri Feb 02 02:59:59 2007