**** BEGIN LOGGING AT Fri Mar 18 02:59:57 2011 Mar 18 03:12:58 .seen prusajr Mar 18 03:13:25 i took a picture of the current state of my reprap project Mar 18 03:13:41 which has been proceding rather slowly Mar 18 03:13:41 heh Mar 18 03:13:46 http://jerkface.net/~joe/reprap/P1010747.JPG Mar 18 03:14:54 This is the generation 3 electronics with ATX powers supply. Notice I modified the y base board in order to have a shelf on one side to accomodate the mainboard and extruder controller and a large platform on teh other side to accomodate the ATX power supply Mar 18 03:15:10 that way i dont mount in circuites over the heatbed and my power supply is tightly coupled Mar 18 17:33:52 hello Mar 18 17:34:26 I have problem accessing U-Boot in NOR flash Mar 18 17:35:34 I tried to follow the instruction steps but didn't succeed Mar 18 17:36:21 Any sugestions? Mar 18 17:37:03 I'm holding AUX and power button but nothing shows up Mar 18 17:53:33 RvX: hi Mar 18 17:53:46 RvX: are you sure your battery is not depleted? Mar 18 17:54:44 RvX: if you're sure, then take out the battery, unplug the device, wait for 5 seconds, plug the battery, press and hold AUX, press power. Mar 18 18:02:11 PaulFerster: Yes, I'm sure. I tried taking out the battery, pluging it again and I have no idea how to deal with it Mar 18 18:03:13 RvX: how did you verify that the battery is not depleted? Mar 18 18:03:45 PaulFerster: Because the OpenMoko loads Mar 18 18:04:01 RvX: does the button work there? Mar 18 18:04:19 RvX: then fully boot the system and ssh to it, we'll check what's in your NOR. Mar 18 18:04:58 PaulFertser: all right Mar 18 18:05:08 If not -- well, faulty NOR button is a common case. Mar 18 18:06:07 PaulFertser: I'm in root@om-gta02:~# Mar 18 18:06:22 from my pc Mar 18 18:06:51 RvX: hexdump -C -n 256 /dev/mtd0 Mar 18 18:07:30 00000000 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| Mar 18 18:07:32 * Mar 18 18:07:33 00000100 Mar 18 18:08:25 RvX: is it a prototype? Looks like your NOR is blank. Do you have a debug board or do you have some soldering skills? Mar 18 18:09:53 PaulFertser: this device (A7) has been used as demo once Mar 18 18:10:19 And yes, I have a debug board Mar 18 18:11:17 RvX: http://wiki.openmoko.org/wiki/Flashing_NOR Mar 18 18:12:20 RvX: you can try my nor image from http://paulfertser.info/files/gta02/nor-uboot.img Mar 18 18:16:06 PaulFertser: ok, thanks. do you have any scheme on how to connect moko with debug board and then with pc? Mar 18 18:16:46 This is the process I'm aware of Mar 18 18:16:48 RvX: it's all on the wiki, basically you connect the debug board with the flexicable to the target, and connect the dboard itself via usb to PC. Mar 18 18:17:14 And you can use another usb cable to connect to the FR itself. Mar 18 18:24:54 PaulFertser: so it looks like I have to get a screwdriver first Mar 18 18:25:29 RvX: you can use a fitting flat screwdriver too Mar 18 18:30:30 ok, thanks for the information Mar 19 01:04:37 PaulFertser: are you still here? I have a problem flashing NOR - the output after executing flashing script is: 1+0 records in Mar 19 01:04:38 1+0 records out Mar 19 01:04:39 2097152 bytes (2.1 MB) copied, 0.00989574 s, 212 MB/s Mar 19 01:27:07 got it :D **** ENDING LOGGING AT Sat Mar 19 02:59:56 2011