**** BEGIN LOGGING AT Mon Dec 08 02:59:57 2008 Dec 08 08:23:02 juhosg * r13542 /trunk/target/linux/ar71xx/files/drivers/net/ag71xx/ag71xx_main.c: [ar71xx] ag71xx driver: remove unused code Dec 08 08:24:49 juhosg * r13543 /trunk/target/linux/ar71xx/files/drivers/net/ag71xx/ag71xx_main.c: [ar71xx] ag71xx driver: interrupt status is masked by hw, don't mask it again Dec 08 08:31:27 juhosg * r13544 /trunk/target/linux/ar71xx/files/drivers/net/ag71xx/ag71xx_main.c: [ar71xx] ag71xx driver: don't refill rx buffers twice Dec 08 13:15:16 juhosg * r13545 /trunk/target/linux/ar71xx/files/drivers/net/ag71xx/ (ag71xx.h ag71xx_main.c): [ar71xx] ag71xx driver: add OOM handler Dec 08 13:23:13 kaloz * r13546 /trunk/target/linux/generic-2.6/ (45 files in 3 dirs): add generic 2.6.28 patches Dec 08 13:25:02 \o/ Dec 08 13:34:00 yuhu Dec 08 13:34:01 :) Dec 08 13:57:23 lo CyrusFF Dec 08 13:57:34 lo blogic Dec 08 14:00:18 wow Dec 08 14:00:45 Kaloz on bleeding edge :) Dec 08 14:02:15 hi juhosg, blogic, CyrusFF, loswillios Dec 08 14:02:21 danage: huh? Dec 08 14:15:01 florian * r13547 /trunk/target/linux/brcm63xx/files/include/asm-mips/mach-bcm63xx/ (bcm63xx_cpu.h bcm63xx_regs.h): Prepare bcm63xx for SPI master support Dec 08 14:46:07 kaloz * r13548 /trunk/target/linux/ixp4xx/ (6 files in 2 dirs): preliminary ixp4xx 2.6.28 support Dec 08 16:25:44 florian * r13549 /trunk/target/linux/brcm63xx/files/arch/mips/bcm63xx/boards/board_bcm963xx.c: Enable ohci on bcm96348gw Dec 08 17:29:42 hi Dec 08 17:29:48 aroscha: huh? Dec 08 17:29:51 kaloz: ping Dec 08 17:32:54 what are the experiences with pronghorn boards so far? are they usable under openwrt? Dec 08 17:39:58 iirc they are usable with openwrt Dec 08 17:43:04 there is an announcement on the main openwrt.org page that says they are fully supported. Dec 08 17:46:05 nbd: nice :) any special .config settings that I should know of? Dec 08 17:46:42 bartman007: yes, i read that :) but sometimes I wish I had not made some announcement on olsr.org (only to find out later that there are in fact some bugs hidden somehwere... eheh) Dec 08 17:47:03 so, just checking if the claim from the homepage still holds or if there are any differences Dec 08 17:48:18 aroscha: this is the point where I stop being useful, I don't have any boards from ADI :) Dec 08 17:48:41 ok, well ... then I will simplyreport bugs as soon as "my precious" will arrive from the customs hehe Dec 08 17:52:34 aroscha: usually you don't need to do special .config stuff for such boards Dec 08 17:52:43 ok, nice Dec 08 17:53:11 Is it all ADI boards or just the pronghorn metro Dec 08 17:53:22 just the pronghorn Dec 08 17:53:28 ah... Dec 08 17:53:31 dont; know Dec 08 17:53:36 misunderstood the last question Dec 08 17:53:56 question... how does one get commit standing? Dec 08 17:54:08 I ment all the variations of the pronghorn (I remember someone having issues with the smaller ones at one point) Dec 08 17:55:42 I have a guy that's frankly getting tired of his patches being ignored... and he's done some good work... Dec 08 17:57:59 anyone? Dec 08 18:06:21 johnrw: I'll be done with finals this friday, I'll have time to test/commit patches Dec 08 18:06:53 what name should I look out for? :) Dec 08 18:07:19 Jose Vasconcellos Dec 08 18:08:16 ok. thanks. Dec 08 18:08:45 He really needs his own commit access... or your gonna lose him... He did the Actiontech MI424WR all by himself... and he cracked the NASTY pci bug noz and I have had with the USR8200... Dec 08 18:09:33 I frankly... was pulling my hair out... because MY units had it... and noz's didn't Dec 08 18:10:27 Hi Folks, jose here. John seems quite impressed by my efforts. But more to the point, I'd like to contribute but it's not clear how to do that. Dec 08 18:10:34 welcome to #openwrt-devel! Dec 08 18:10:58 No... IS DAMN IMPRESSED... Dec 08 18:11:23 :) Dec 08 18:13:03 MateIn4: I feel kinda dumb, my mi424wr doesn't wan't to boot and I appear to be missing something simple when it comes to making openocd work for jtag Dec 08 18:14:03 Bartman007: 1st verify that you have a rev A unit. I've talked to another user that has rev D and it seems that the HW is different. Dec 08 18:14:18 I had tried bumping ruby to 1.8.7 independenty but it broke, I'll test your ruby patch, wpa-supplicant and hopefully a few other things Dec 08 18:15:02 Bartman007: 2nd, there's a jungo-image script that can install redboot without the need for JTAG. Dec 08 18:15:22 MateIn4: it doesn't even want to boot with stock firmware ATM, so I need to make sure it functions before I do anything else Dec 08 18:15:23 Just so you folks know... If you look at the USR8200 wiki... and see where the Redboot mfill commands are issued... Well that's Jose's debugging skills... at work... heck he told me a week ago... and I finally got it Saturday night... without that cmd... pci is quite useless. Dec 08 18:16:15 Bartman007: got it Dec 08 18:16:50 but IIRC at least some of your mi424 patches have already been committed Dec 08 18:17:37 Bartman007: yes, the main patch is there. what's missing is defect #4134 and a config file. Dec 08 18:17:48 Now this patch... I have used... and all of a sudden... my builds stop building a bunch of IXP42x targets I don't need... https://dev.openwrt.org/ticket/4134 Dec 08 18:19:23 It was very usefull... because one time I was building an image that one of those targets didn't have the memory capacity for... and so my build stopped... (That's when I went and got the patch!) Dec 08 18:20:44 I have 16mb flash... and so when I was filling it up with goodies... I think it was the nslu2 that couldn't hold that much stuff... and the build stopped... Dec 08 18:22:19 MateIn4: I never told you that did I :) Dec 08 18:22:30 That's why I made that patch! Dec 08 18:22:36 lol Dec 08 18:23:11 Gotcha... Dec 08 18:23:26 MateIn4: one more thing to add to the list :) Dec 08 18:25:33 Well if any of you guys have an ixp based problem... you will do good to seek out Jose... me you can(and do) ignore... :) Dec 08 18:26:48 I've learned alot bug hunting with him Dec 08 18:26:51 Unto another topic: RT2500pci wifi, current trunk is broken Dec 08 18:28:11 Perhaps there's not much interest in this card. Dec 08 18:30:03 rt2500 broken? Dec 08 18:30:34 it doesn't build properly as the crypto module is missing Dec 08 18:31:42 a more important problem for 2.6.27 developers is that the mac80211 Makefile references a file doesn't exists anymore! Dec 08 18:33:13 for downloading, not sure why the switch from orbit-lab.org to wireless.kernel.org was made as the latter doesn't keep old versions. Dec 08 18:33:54 well I don't have any rt2500pci's, but I do have a rt8187 usb based adapter I'd like to do more than 'client mode' with... : Dec 08 18:34:19 johnrw: that's a completely different chipset Dec 08 18:34:47 It uses the mac80211 Dec 08 18:35:22 but ok... Dec 08 18:35:23 the issue is only if you are using 2.6.27 and need to download a fresh version Dec 08 18:36:52 right... ok... I need more coffee... Dec 08 20:13:28 noz * r13550 /trunk/scripts/jungo-image.py: Dec 08 20:13:28 Updated jungo-image.py script (from Jose): Dec 08 20:13:28 Fix http server issues when imagefile is on different directory Dec 08 20:13:28 Fix computation of flash size Dec 08 20:13:28 Obtain MAC address in a more portable way Dec 08 20:13:29 Add percent display when dumping flash (instead of dots) Dec 08 20:13:33 Set default to display progress information; added --quiet option Dec 08 21:00:04 florian * r13551 /trunk/target/linux/brcm63xx/files/drivers/mtd/maps/bcm963xx-flash.c: Fix remaining bug of the off-by-one error ;) Dec 08 21:00:41 hehe Dec 08 21:01:00 <[florian]> mouahaha Dec 08 22:05:37 florian * r13552 /trunk/package/kexec-tools/Makefile: kexec-tools builds fine again on 2.6.27, unmask it and also make it available for mips (be) targets Dec 08 23:54:37 cryptotools is failing to build on 8.09 packages: Dec 08 23:54:38 error: crypto/cryptodev.h: No such file or directory Dec 09 00:25:25 rwhitby * r13553 /branches/8.09/package/ocf-crypto-headers/: Backport ocf-crypto-headers to 8.09, to enable crypto-tools to compile (build dependency only) Dec 09 00:26:41 rwhitby * r13554 /packages/utils/crypto-tools/Makefile: crypto-tools: Add build dependency on ocf-crypto-headers. Dec 09 00:49:07 mirko * r13555 /packages/Xorg/lib/ (ecore/Makefile eet/Makefile): disable gnutls-support in ecore and eet Dec 09 01:53:09 nbd * r13556 /trunk/target/linux/atheros/files/arch/mips/atheros/ar5315/board.c: atheros: fix reboot on ar2315 devices which do not implement the atheros reference design workaround for the buggy reset logic (e.g. some senao stuff) Dec 09 02:12:21 lars * r13557 /packages/Xorg/app/x11perf/ (. Makefile): Add x11perf. **** ENDING LOGGING AT Tue Dec 09 02:59:57 2008