**** BEGIN LOGGING AT Thu Apr 26 03:00:00 2012 Apr 26 05:08:28 dwmw2_gone: avoid patch bombs, just give people time the respond on your git pull request Apr 26 08:35:06 I see an odd problem with attitude adjustment (r31296)... on boot, very frequently the lan network interfaces are configured and up, but don't respond to any traffic until I logon via the serial console and do an outward ping...at which point the dhcp clients get their addresses and everything works. But the lan network doesn't work until I do the outward ping. Anybody also seen that? Apr 26 08:39:47 CaneToad: which target/device? Apr 26 08:40:57 Skyline SL-R7205 Wireless 3G Router - Ralink RT3052 id:1 rev:3, MIPS 24KEc V4.12 Apr 26 08:46:31 does it have an external switch, or does it use the internal one? (swconfig dev switch0 help should tell you) Apr 26 09:15:30 KanjiMonster: swconfig isn't installed, I'll have to build it Apr 26 09:23:08 KanjiMonster: it says "Failed to connect to the switch" Apr 26 09:25:15 KanjiMonster: so I presume the internal one then? Apr 26 09:33:12 KanjiMonster: https://forum.openwrt.org/viewtopic.php?pid=149441 says "There is currently no support for swconfig in ramips" Apr 26 12:56:45 hi Apr 26 13:02:29 tripolar * r31482 /packages/net/openssh/ (3 files in 2 dirs): [packages/openssh] update openssh to 6.0p1 Apr 26 13:15:21 tripolar * r31483 /packages/net/openssh/patches/200-dscp-qos.patch: [packages/openssh] refresh 200-dscp-qos.patch too Apr 26 14:59:33 build #5 of s3c24xx is complete: Failure [failed compile_4] Build details are at http://buildbot.openwrt.org:8010/builders/s3c24xx/builds/5 Apr 26 17:54:02 nbd * r31484 /trunk/ (4 files in 3 dirs): (log message trimmed) Apr 26 17:54:02 build: rework verbosity level selection Apr 26 17:54:02 V=99 and V=1 are now deprecated in favor of a new verbosity class system, Apr 26 17:54:02 though the old flags are still supported. Apr 26 17:54:02 You can set the V variable on the command line (or OPENWRT_VERBOSE in the Apr 26 17:54:03 environment) to one or more of the following characters: Apr 26 17:54:04 - s: stdout+stderr (equal to the old V=99) Apr 26 17:54:05 nbd * r31485 /trunk/include/cmake.mk: cmake: add support for V=cs Apr 26 17:54:26 I recently put an TP Link TL-WN961N into my Alix, and put in 3 rubber ducks... the 18cm 7dBmi antennae... Apr 26 18:09:01 the signal strength is terrible! I was wondering if there was a glitch in the ath5k drivers or I needed to explicitly configure this to make it operate more optimally. Apr 26 18:09:53 what signal strength do you get over what distance? Apr 26 18:10:45 my clients are an iPod, an iPhone, and a macbook. not sure if there's a way to measure that on any of these platforms. Apr 26 18:11:21 I'm going through 2 sheetrock walls, about... not more than 10m. Apr 26 18:11:21 then how do you know that the signal strength is bad? Apr 26 18:12:08 well, I see the signal strength icon on all 3 devices drop to 1 or 2 rings... and the throughput is under 5mb/s. Apr 26 18:12:12 also seeing this: Apr 26 18:12:16 00:0c.0 Network controller: Atheros Communications Inc. AR5416 Wireless Network Adapter [AR5008 802.11(a)bgn] (rev 01) Apr 26 18:12:18 Subsystem: Atheros Communications Inc. Device 2071 Apr 26 18:12:19 Flags: bus master, 66MHz, medium devsel, latency 168, IRQ 9 Apr 26 18:12:21 Memory at e0080000 (32-bit, non-prefetchable) [size=64K] Apr 26 18:12:23 Capabilities: [40] #80 [0000] Apr 26 18:12:24 Kernel driver in use: ath9k Apr 26 18:12:37 which confuses me... it's an AR5416, but it's using the ath9k drivers??? Apr 26 18:13:20 nbd * r31486 /trunk/include/verbose.mk: build: fix bad file descriptor issues with the verbosity changes Apr 26 18:13:51 ar5416 is the first generation 802.11n device from atheros Apr 26 18:14:02 it's a rather buggy chipset Apr 26 18:14:07 wouldn't recommend it for any serious use Apr 26 18:24:03 damn. Apr 26 18:24:25 well, it's the only 3-antennae miniPCI card out there that I could find... Apr 26 18:24:31 any other suggestions? Apr 26 18:28:44 get a two-antenna one Apr 26 18:46:15 ar9220 based Apr 27 00:10:49 i've built a package i'd like to contribute upstream... what would be the best way to go about submitting the Makefile ? Apr 27 00:13:03 it's not really a patch per se, just a couple of additional files Apr 27 00:17:44 vineyard: submit it as a patch to openwrt-devel mailing list Apr 27 00:18:07 * luka12345 is off to bed Apr 27 00:18:32 even though it's not modifying any existing files (just adding) ? Apr 27 00:18:38 yes Apr 27 00:19:19 ok, i'll read the faq on submitting patches, i'm assuming you want a diff -u against the trunk root ? Apr 27 00:20:07 or svn diff perhaps Apr 27 00:20:40 pkg builds cleanly against at least backfire and trunk - not much to it really Apr 27 01:09:57 Hi Apr 27 01:10:24 How to add 'wlan0' under command line? Apr 27 01:11:51 depends on the driver Apr 27 01:12:04 assuming mac80211 it would be something like Apr 27 01:12:13 iw phy phy0 interface add wlan0 type station Apr 27 01:14:25 jow_laptop, thanks. that is working. **** ENDING LOGGING AT Fri Apr 27 03:00:00 2012