**** BEGIN LOGGING AT Thu Dec 23 02:59:58 2010
Dec 23 11:17:25 <ceka> hello
Dec 23 11:17:43 <ceka> i have a beagleboard card
Dec 23 11:18:18 <ceka> but i can't connect internet via console
Dec 23 11:18:43 <ceka> how i can set up internet connection?
Dec 23 11:18:59 <ceka> help,please.
Dec 23 11:38:53 <ceka> is there anyone?
Dec 23 13:00:41 <DJWillis> ceka: it would help if you told people what BeagleBoard you had and what device your using to connect it to the network ;).
Dec 23 13:01:05 <ceka> beagleboard rev c3
Dec 23 13:01:19 <DJWillis> Yep, and?
Dec 23 13:01:35 <ceka> and i try to cennect internet viausb wireless adaptor
Dec 23 13:01:42 <ceka> *connect
Dec 23 13:02:24 <DJWillis> Is it found, drivers installed etc.? Checked dmesg?
Dec 23 13:02:24 <ceka> but when i try iwconfig key #password
Dec 23 13:02:29 <ceka> it doesnt set
Dec 23 13:02:35 <ceka> yes
Dec 23 13:02:46 <ceka> it can scan andsee my wireless network
Dec 23 13:02:51 <DJWillis> So is it a WPA network? 
Dec 23 13:03:03 <ceka> yes, wpa2
Dec 23 13:03:35 <DJWillis> Well your trying to set a WEP key ;), are you running a GUI on there? You will need something like WPASuplicant
Dec 23 13:04:12 <ceka> i installed 2010.3 rootfs
Dec 23 13:04:33 <ceka> but i don't have a monitor with hdmi
Dec 23 13:04:49 <ceka> so i connect beagleboard via rs232
Dec 23 13:05:09 <DJWillis> Well do you have WPASuplicant in that rootfs (not got it handy to check), a few guides on the net will help with that.
Dec 23 13:05:11 <ceka> i'm using  it for my thesis project
Dec 23 13:05:54 <ceka> i think wpa_supplicantinstalled,becasue /etc/wpa_supplicantfolder exist
Dec 23 13:06:31 <pupnik> the package could have some problems.  help fix
Dec 23 13:06:58 <DJWillis> So have a read of guides on WPA with the command line, that's the sort of place you want to start.
Dec 23 13:08:39 <DJWillis> ceka: it sounds like you have everything you need, just some magic needed to tie it all up on the command line :), I guess you could also install network managers cli and use that to setup the connection, it's in the repros so you would just need to copy over the IPK's (via SD etc.)
Dec 23 13:09:34 <ceka> DJWillis: me,too. i want to internet connection for installing opencv
Dec 23 13:09:43 <ceka> becasue it hasalot of depends
Dec 23 13:10:43 <DJWillis> Yep, so have a google about ;). http://linux.icydog.net/wpa.php for example (at a quick look).
Dec 23 13:12:09 <DJWillis> ceka: it's that sort of thing you will need to setup assuming your adaptor can scan and see the network but not deal with the encryption.
Dec 23 13:12:50 <ceka> DJWillis: you're great!İ have read a lot of pages about the subject
Dec 23 13:13:10 <ceka> but this page is good
Dec 23 13:13:26 <DJWillis> ceka: if you can't get it going pop back, but I suspect that is just about what you need.
Dec 23 13:21:22 <ceka> ok,DJWillis. i removed angstrom for trying ubunut armport. i going to reinstall angstrom and try it
Dec 23 14:25:12 <ceka> DJWillis: are you there?
Dec 23 14:47:42 <ceka> what ever,i downlaod new own build angstrom that is icluded opencv,gcc,vs
Dec 23 14:48:05 <ceka> so,i don't need internet connection for beagleboard
Dec 23 14:48:18 <ceka> but,thank you very much again
Dec 23 15:03:37 <omapuser> can anyone help me aboıt apache2 + php configuration on hawlkboard angstrom?
Dec 23 16:23:59 <pupnik> what's the gitorious.org ip address?
Dec 23 16:28:31 <pupnik> http://87.238.52.168/ 
Dec 23 20:44:33 <chrisw957_home> Is the best way to write the mac address in the eeprom of my lan9221 to use ethtool?  I tried opkg install ethtool on my overo but it wasn't found.
Dec 23 21:04:27 <pupnik> http://www.angstrom-distribution.org/simplified-development-setup   <<< broken
Dec 23 21:05:11 <pupnik> ./oebb.sh bitbake pandora
Dec 23 21:05:11 <pupnik> Using ~/.oe/environment to setup needed variables. It is recommended to do '. ~/.oe/environment' and run 'bitbake something' without using ./oebb.sh as wrapper
Dec 23 21:05:14 <pupnik> Executing: bitbake pandora
Dec 23 21:05:16 <pupnik> NOTE: Handling BitBake files: / (0002/7258) [ 0 %]ERROR: Unable to determine endianness for architecture 'INVALID'
Dec 23 21:08:15 <pupnik> following that suggestion yields 
Dec 23 21:08:16 <pupnik> . ~/.oe/environment 
Dec 23 21:08:16 <pupnik> pupnik@bronchi:~/AngstromDev/angstrom-setup-scripts$ bitbake pandora
Dec 23 21:08:17 <pupnik> NOTE: Handling BitBake files: / (0002/7258) [ 0 %]ERROR: Unable to determine endianness for architecture 'INVALID'
Dec 23 21:21:27 <pupnik> hola kolla
**** BEGIN LOGGING AT Fri Dec 24 01:26:45 2010
**** ENDING LOGGING AT Fri Dec 24 02:59:58 2010