**** BEGIN LOGGING AT Wed Aug 10 02:59:56 2022
Aug 10 09:31:58 <Angad> Hi, I am getting this error while running LEDscape library in my beaglebone black: pru_init:44: prussdrv_open open failed
Aug 10 09:31:58 <Angad> Can someone help me to fix this error?
Aug 10 09:34:35 <zmatt> Angad: I replied to you last time you were here: https://libera.irclog.whitequark.org/beagle/2022-08-08#1659961628-1659962094;
Aug 10 09:36:10 <Angad> Sorry i missed your message
Aug 10 09:36:53 <Angad> I will try and tell you know.
Aug 10 09:36:53 <Angad> Thanks zmatt
Aug 10 10:19:00 <Angad> thanks, the error is gone but not able to figure out which pins im supposed to connect my leds to (P9_22 isnt working). thanks for the help
Aug 10 10:22:10 <zmatt> I don't really know much about LEDscape or what pins it uses for what, but be sure the pin(s) used are pinmuxed appropriately, e.g.:
Aug 10 10:22:17 <zmatt> config-pin P9_22 pruout
Aug 10 10:22:53 <zmatt> in general, config-pin PIN MODE   where MODE is "pruout" for outputs used by PRU or "pruin" for inputs used by PRU
Aug 10 10:24:04 <zmatt> ehh, but P9_22 has no pruout/pruin functionality though, you sure you got that right?
Aug 10 10:27:19 <Angad> was following this https://beagleboard.org/static/prucookbook/#_neopixels_5050_rgb_leds_with_integrated_drivers_ledscape
Aug 10 10:28:04 <zmatt> oh it looks like for ws2812 it uses normal gpios rather than dedicated pru outputs
Aug 10 10:28:13 <zmatt> I guess because ws2812 is a slow enough protocol
Aug 10 10:28:24 <zmatt> so in that case you don't need to do anything with config-pin
Aug 10 10:28:38 <zmatt> but you probably need to configure the gpio(s) as output
Aug 10 10:29:41 <zmatt> you're using the Yona-Appletree fork of LEDscape?
Aug 10 10:32:15 <Angad> Thanks, Now its working
Aug 10 10:32:19 <Angad> Thanks a lot
Aug 10 10:32:22 <zmatt> ok!
Aug 10 22:14:24 <set_> I am made it back!
Aug 10 22:14:50 <set_> Yes, I am!
Aug 10 22:21:10 <set_> Now...down to beeswax. Um, has any person in life, esp. in this board, held the EVEs on the BBAI in use?
Aug 10 22:24:50 <set_> or has anyone used the DSP(s) on the BBAI for anything other than rtos?
Aug 10 22:26:22 <set_> I found DSPlib but it is for the rtos on the BBAI, e.g. the ICE unit actually most likely.
Aug 10 22:28:45 <set_> Anyway, just a general question...
Aug 10 22:29:07 <set_> I am trying to sneak some info. from you if it is you that knows about these co-processors.
Aug 10 22:30:52 <set_> I have forty million docs. on these things (TOO MUCH). I will never be able to round them all together into an actual application.
Aug 10 22:31:27 <set_> Anyway, that is the plight of the day. Geaux Cajuns.
**** ENDING LOGGING AT Thu Aug 11 02:59:56 2022