**** BEGIN LOGGING AT Sat Sep 06 02:59:57 2008 Sep 06 11:44:44 hi Sep 06 11:46:14 I've got problems with iptable kernel module in my uNSLUng-6.10-beta Sep 06 11:47:09 when I'm installing it from ipkg i have http://pastebin.com/m45dbdf76 Sep 06 11:49:02 anyone can tell me wtf is going on? Sep 06 12:07:32 hm, i'd check the output of dmesg Sep 06 17:28:56 hjey guyas Sep 06 17:29:48 can anyone recomend a firmware for nslu2? which is easier on installing packages unslung or openwrt? Sep 06 17:37:43 I recommend slugos/be Sep 06 18:37:44 neone here? Sep 06 18:40:20 * mwester looks around for "neone" Sep 06 18:42:26 lol Sep 06 18:42:37 port 80 on my nslu2 is closed?? Sep 06 18:42:39 any ideas? Sep 06 18:42:52 Not with so little information Sep 06 18:43:09 You didn't even tell anyone why you would expect it to be open! Sep 06 18:43:27 well i thought by default it was open in 192.168.1.77 Sep 06 18:43:48 Depends on the firmware, and what software you've installed, and config changes you may have made, of course. Sep 06 18:43:50 i can ping it.. but when i try to get http is fauls Sep 06 18:44:02 SlugOS and Debian do not have anything on port 80 by default Sep 06 18:44:12 well i bought it used off eba and have not made any changes yet Sep 06 18:44:13 Unslung does, but you can change it or move it away. Sep 06 18:44:25 Ah, well... Sep 06 18:44:32 no upgraded firmware yet.. defualt im assuming Sep 06 18:44:43 First rule for ANY device you buy used -- reflash it immediately! Sep 06 18:45:10 Use the "reset button" technique to put it into upgrade mode, then use the windows or Linux utility to upload the new firmware. Sep 06 18:45:28 Then reset it to factory defaults using the reset button (Linksys instructions). Sep 06 18:45:38 From there you can start with a fresh device. Sep 06 18:45:54 k the book says 10 seconds... but that doesnt work should i try longer? Sep 06 18:46:04 It's actually closer to 11 seconds. Sep 06 18:46:10 (by my count). Sep 06 18:46:48 As the wiki pages should note, the color change at the 10/11 second mark is very subtle -- some people have reported that they need to dim the light in the room to detect it. Sep 06 18:46:55 But it ALWAYS works... Sep 06 18:49:14 ok got it in upgrade mode and its upgrading Sep 06 18:49:27 then to do the defaults hold the reset for 10 while its on? Sep 06 18:54:25 sUb_ZeRo1: I don't recall; perhaps that's in the wiki somewhere. Sep 06 20:07:46 i flashed unslung and still no web interface Sep 06 20:08:22 port 80 is still closed.. i thoguth flashing unslung would reset ip to 192.168.1.77 and reset passwords.. is this correct? Sep 06 20:15:21 lo lnow it wont even turn off... it just beeps twice every 10 seconds Sep 06 20:30:26 sub_ZeRo: Reflashing does not change the settings; you need to do the reset to factory defaults in order to have that happen. Sep 06 20:30:53 Linksys stores network and config information in a separate area of the device that is not altered by the firmware reflashing process. **** ENDING LOGGING AT Sun Sep 07 02:59:57 2008