**** BEGIN LOGGING AT Thu Apr 01 02:59:57 2010
Apr 01 05:39:05 <numen> hi
Apr 01 05:39:44 <numen> can anyone provide me a complete flash image? read with jtag
Apr 01 14:12:32 <Mikeinaus> Hi
Apr 01 14:12:52 <Mikeinaus> are there any cortex M3 programmers in here??
Apr 01 16:08:36 <numen> hi
Apr 01 18:24:48 <nickoe> Hi
Apr 01 19:48:20 <luv2chill> ok what am i missing? slugos/le 5.3 if I turnup to RAID1 (/dev/md0) then md0 gets created successfully at bootup, but the performance on that was killing me so i turned up to a separate usb hard disk. Now, even though I create /dev/md0 with the two flash drives...
Apr 01 19:48:31 <luv2chill> they will not re-assemble automatically after a reboot
Apr 01 19:49:12 <luv2chill> i can manually run mdadm --assemble and they work fine, but as soon as i reboot, /dev/sdb1 and /dev/sdc1 (the two drives making up the raid1) get mounted inidividually
Apr 01 19:49:43 <luv2chill> i have to umount them and then run mdadm --assemble again, which works until the next reboot, etc.
Apr 01 19:49:46 <numen> have you done the correct entries in the mdadm config file?
Apr 01 19:50:40 <luv2chill> i created mdadm.conf by doing a # mdadm --detail --scan >/etc/mdadm.conf
Apr 01 19:50:57 <luv2chill> per wiki here: http://www.nslu2-linux.org/wiki/SlugOS/TurnupToRAID
Apr 01 19:51:19 <numen> what does your fstab tell?
Apr 01 19:52:05 <luv2chill> contents of mdadm.conf are thus: ARRAY /dev/md0 level=raid1 num-devices=2 UUID=19f18cf9:b99ca0e0:fedd0733:f6f7b803
Apr 01 19:52:37 <numen> could you nopaste your fstab?
Apr 01 19:52:38 <luv2chill> proc            /proc           proc    defaults        0  0
Apr 01 19:52:38 <luv2chill> tmpfs           /var/volatile   tmpfs   mode=0755       0  0
Apr 01 19:52:38 <luv2chill> #tmpfs          /media/ram      tmpfs   defaults        0  0
Apr 01 19:52:38 <luv2chill> tmpfs           /dev/shm        tmpfs   mode=0777       0  0
Apr 01 19:52:38 <luv2chill> usbfs           /proc/bus/usb   usbfs   defaults        0  0
Apr 01 19:52:51 <numen> there is something missing like
Apr 01 19:53:02 <luv2chill> yeah it didnt include the lines that begin with /
Apr 01 19:53:06 <luv2chill> one sec
Apr 01 19:53:18 <luv2chill> like /dev/sda1       /       ext3    noatime 1  1
Apr 01 19:53:27 <luv2chill> that is boot drive (turnup to that drive)
Apr 01 19:53:40 <luv2chill> then i tried to add manually /dev/md0 /svn ext3 defaults 0 0
Apr 01 19:54:02 <luv2chill> but it doesn't seem to make any difference
Apr 01 19:54:14 <numen> you should have something like /dev/md0 <mountpoint> <fs> <options> 0 0
Apr 01 19:54:24 <luv2chill> see above
Apr 01 19:54:42 <luv2chill> i have a line: /dev/md0 /svn ext3 defaults 0 0
Apr 01 19:56:18 <numen> seen
Apr 01 19:56:28 <numen> could you nopaste your mdadm.conf?
Apr 01 19:56:43 <luv2chill> i did already... one sec
Apr 01 19:56:55 <luv2chill> [14:52] <luv2chill> contents of mdadm.conf are thus: ARRAY /dev/md0 level=raid1 num-devices=2 UUID=19f18cf9:b99ca0e0:fedd0733:f6f7b803
Apr 01 19:56:56 <numen> but nopaste
Apr 01 19:57:01 <numen> not in channel
Apr 01 19:57:33 <luv2chill> oh sorry
Apr 01 19:57:39 <luv2chill> nopaste.voric.com?
Apr 01 19:59:12 <luv2chill> http://nopaste.voric.com/paste.php?f=bol3cl
Apr 01 20:02:43 <numen> mhm
Apr 01 20:02:45 <numen> strange
Apr 01 20:04:38 <luv2chill> only thing I havent tried is changing mdadm.conf to load by specifying the members (/dev/sdb1 /dev/sdc1) instead of UUID
Apr 01 20:04:49 <numen> # sed s/' UUID="$uuid" '/' "$device" '/ </sbin/turnup >/tmp/turnup-patched
Apr 01 20:04:49 <numen> # sh /tmp/turnup-patched memstick -i /dev/md0
Apr 01 20:04:54 <numen> this you have done, too?
Apr 01 20:05:05 <luv2chill> but i would like to avoid that since i cant guarantee that those drives will always be sdb1 and sdc1
Apr 01 20:05:28 <luv2chill> yes i did that, but i do not want to turn up to the raid array
Apr 01 20:05:38 <luv2chill> i turned up to /dev/sda1
Apr 01 20:05:49 <luv2chill> raid array is for extra storage
Apr 01 20:05:59 <numen> mhm
Apr 01 20:06:02 <luv2chill> it was too slow using it for the entire file system
Apr 01 20:06:03 <numen> dont know...
Apr 01 20:06:14 <luv2chill> ok, well thank you for trying
Apr 01 20:06:36 <numen> i used raid earlier
Apr 01 20:06:39 <numen> but not on slug
Apr 01 20:06:41 <luv2chill> btw do you know anything about the oom killer?
Apr 01 20:06:49 <numen> nope?
Apr 01 20:06:54 <numen> do you have a jtag?
Apr 01 20:06:59 <luv2chill> nope 
Apr 01 20:07:12 <numen> i need a complete flash image...
Apr 01 20:07:14 <luv2chill> you bricked you slug?
Apr 01 20:07:17 <numen> i destroyed redboot
Apr 01 20:07:20 <numen> i did
Apr 01 20:07:22 <luv2chill> ouch
Apr 01 20:07:27 <luv2chill> that sucks
Apr 01 20:07:35 <numen> but yesterday i missed an mistake while jtag
Apr 01 20:07:45 <numen> and erased adress 0x0000000
Apr 01 20:07:51 <numen> instead 0x50000000
Apr 01 20:07:57 <luv2chill> ahh shit
Apr 01 20:08:21 <numen> now i need the stuff from zero till 0x4FFFFFFF
Apr 01 20:08:26 <numen> for flashing...
Apr 01 20:08:33 <luv2chill> i wish i could help you but ive no experience with the bootloaders and such
Apr 01 20:08:58 <luv2chill> unfortunately slugs arent as popular as they used to be
Apr 01 20:09:10 <luv2chill> so the community has died down a bit
Apr 01 20:10:03 <numen> you dont no one with an jtag?
Apr 01 20:10:12 <numen> flashing is not the problem, but i need the image first^^
Apr 01 20:11:08 <luv2chill> no i dont have any jtag for the slug (or any other device)
Apr 01 20:11:16 <luv2chill> but hopefully someone here does
Apr 01 20:12:28 <numen> noone found allready
Apr 01 20:12:44 <luv2chill> did you try any of the other nslu2 channels?
Apr 01 20:12:56 <numen> which?
Apr 01 20:13:22 <luv2chill> •#nslu2-general 
Apr 01 20:13:22 <luv2chill> •#nslu2-linux 
Apr 01 20:13:22 <luv2chill> •#ds101-linux 
Apr 01 20:13:22 <luv2chill> •#linkstationwiki 
Apr 01 20:13:22 <luv2chill> •#openslug 
Apr 01 20:13:38 <luv2chill> i dont know maybe they are the same lurkers as here :)
Apr 01 20:14:14 <numen> in general i asked
Apr 01 20:14:22 <numen> in linux noone seems to be
Apr 01 20:14:37 <luv2chill> ah
Apr 01 20:15:36 <luv2chill> well give it a few more days... there is also mailing lists you could try:
Apr 01 20:15:37 <luv2chill> http://www.nslu2-linux.org/wiki/Main/MailingLists
Apr 01 20:18:43 <numen> takes long time reading the whole flash^^
Apr 01 20:19:34 <numen> you arent able to get an jtag debuger?
Apr 01 20:19:41 <numen> or solder in 5minutes yourself
Apr 01 20:19:51 <numen> needs just a few resisters
Apr 01 20:19:51 <luv2chill> no, i dont have the skill
Apr 01 20:20:01 <numen> its quite easy^^
Apr 01 20:20:09 <luv2chill> sorry, i am not low level :)
Apr 01 20:20:13 <luv2chill> no soldering iron
Apr 01 20:22:47 <numen> http://www.nslu2-linux.org/wiki/HowTo/RecoverFromABadFlashUsingJTAG
Apr 01 20:24:26 <luv2chill> if i had the expertise and equipment i would help you... I think you should post a message on the mailing list or hang out here for a few more days to see if someone else already has the flash dumped
Apr 01 20:25:18 <numen> i did a post in the mailing list
Apr 01 20:25:30 <numen> where are u from?
Apr 01 20:27:36 <luv2chill> USA
Apr 01 20:27:42 <luv2chill> you?
Apr 01 20:28:38 <numen> switzerland
Apr 01 20:29:37 <luv2chill> cool, i like switzerland very much
Apr 01 20:30:09 <luv2chill> expensive country but very nice place
Apr 01 20:30:21 <numen> ^^
Apr 01 20:30:27 <luv2chill> :)
Apr 01 20:30:43 <numen> sometimes i would like to be in usa^^
Apr 01 20:31:02 <luv2chill> yeah it has some advantages
Apr 01 20:32:12 <numen> getting gadgets and electronic parts^^
Apr 01 20:35:09 <luv2chill> definitely
Apr 01 20:36:42 <numen> my girlfriend wants an ipad^^
Apr 01 20:37:23 <Lunar_Lamp> Buy her an iPhone and tell her that it just looks bigger in the advertising.
Apr 01 20:37:31 <numen> lol
Apr 01 20:37:33 <luv2chill> lmao
Apr 01 20:37:38 <numen> Lunar_Lamp do you have an jtag?
Apr 01 20:37:55 <Lunar_Lamp> I'm afraid I do not.
**** ENDING LOGGING AT Fri Apr 02 02:59:56 2010