**** BEGIN LOGGING AT Tue Jan 06 02:59:56 2009 Jan 06 07:47:29 qt-embedded help nedded? Jan 06 07:47:35 anyone there? Jan 06 07:51:18 how to activate touchscreen using qt Jan 06 07:51:19 ??? Jan 06 07:51:30 pls help Jan 06 10:31:40 aj1911: what do you mean ? Jan 06 10:31:55 you probably need to enable libts Jan 06 10:32:06 i have compiled qt with tslib Jan 06 10:32:20 and followed following steps : Jan 06 10:32:35 http://www.opentom.org/Tslib Jan 06 10:33:06 how to enabled libts? Jan 06 10:33:08 ?? Jan 06 10:35:07 r u there tsdogs??? Jan 06 10:35:23 hmm, you probably need some environment var Jan 06 10:37:11 hwo to check which enviroment var is missing? Jan 06 10:37:28 export QWS_MOUSE_PROTO="tslib:/dev/input/touchscreen0" Jan 06 10:37:41 export TSLIB_CONFFILE=/etc/ts.conf Jan 06 10:38:01 adapt touchscreen0 to what is your touch input device Jan 06 10:38:57 my touchscreent input device is ttyS0 Jan 06 10:40:27 i'm using UCB1400 controller Jan 06 10:40:56 it's a serial touchscreen then Jan 06 10:41:08 y Jan 06 10:41:22 does tslib support serial devices? Jan 06 10:41:46 i just now found touchscreen input device is Jan 06 10:42:12 dev/input/touchscreen0 Jan 06 10:42:14 good then point it to that one Jan 06 10:42:25 same as u told earlier Jan 06 10:42:35 good, try like that then Jan 06 10:42:57 wait for 2 mins Jan 06 10:46:37 i also followed the steps in the link : http://lists.trolltech.com/qt-embedded-interest/2005-10/thread00014-0.html Jan 06 10:47:57 what version of qt-embedded u using? Jan 06 10:48:58 does ts_calibrate work? Jan 06 10:50:24 gg, bbl Jan 06 10:52:13 when executing command ts_calibrate : Jan 06 10:52:35 error comes: could'nt load ucb14000 module Jan 06 10:52:53 i haven't set QWS_MOUSE_PROTO="tslib:/dev/input/touchscreen0" Jan 06 10:53:06 i will do and get back to u Jan 06 10:59:57 hi Jan 06 11:03:37 hi tsdogs,while executing i get following error : Jan 06 11:03:49 could'nt load ucb14000 module Jan 06 11:04:02 No raw modules loaded Jan 06 11:04:24 ts_config : success Jan 06 11:04:46 what is the problem :( Jan 06 11:05:16 i have set all the enviroment variables Jan 06 11:05:50 i'm using qt-embedded 4.4.1 Jan 06 11:06:07 r u there/ Jan 06 11:06:17 ? Jan 06 11:14:25 you'll first need to make sure tslib is working properly Jan 06 11:14:36 I found this if for any help: http://www.nabble.com/Re%3A-Using-the-UCB1400-as-a-TS-controller-p20777476.html Jan 06 11:16:11 really gg now, cya **** ENDING LOGGING AT Wed Jan 07 02:59:57 2009