**** BEGIN LOGGING AT Sun Mar 06 02:59:57 2011
Mar 06 04:12:57 <Kurlon> First try, flashing 'A N D R O I D _' prompt, kernel fired up, no userland
Mar 06 08:17:07 <noah1989> hi
Mar 06 08:17:35 <noah1989> anyone knows where to get the kernel sources used for natty alpha-2? (omap3)
Mar 06 08:18:25 <noah1989> i am trying to figure out if the dds driver accepts anything else than "tv:ntsc" or "tv:pal" for tv out
Mar 06 08:19:02 <noah1989> (because both of these modes result in an image larger than the screen)
Mar 06 09:40:56 <ogra> noah1989, apt-get source linux
Mar 06 09:43:23 <dmajnem2> hi
Mar 06 09:43:40 <dmajnem2> I have the image from the OMAPMaverickInstall page
Mar 06 09:44:16 <dmajnem2> I was wondering how do I get it to display on the UART by default on my beagleboard
Mar 06 09:44:49 <ogra> there is a section at the bottom linking to a page how to edit boot.scr
Mar 06 09:45:26 <ogra> note though that you will need the monitor for the initial setup tool
Mar 06 09:47:28 <dmajnem2> ogra: thanks, I see the file but it does not seem like it should be modified up front
Mar 06 09:48:04 <ogra> we will have a headless developer image in natty that will default to serial output
Mar 06 09:48:12 <dmajnem2> ah, cool
Mar 06 09:48:15 <ogra> (not yet there)
Mar 06 09:48:20 <dmajnem2> ah, was just about to say
Mar 06 09:48:36 <dmajnem2> how do I modify the scr file? just edit it?
Mar 06 09:49:15 <noah1989> dmajnem2: no. remove the first 72 bytes, save it to boot.cmd and then use mkimage to add the header again
Mar 06 09:49:31 <noah1989> it contains a checksum, so just editing the file will fail
Mar 06 09:49:46 <ogra> https://wiki.ubuntu.com/ARM/BeagleEditBootscr
Mar 06 09:50:08 <dmajnem2> noah1989: that is what I figured, thanks
Mar 06 09:55:31 <dmajnem2> do I need to remove the omapfb.mode stuff?
Mar 06 10:00:18 <bambee> hi, anyone has a toshiba ac100 here ?
Mar 06 10:03:24 <dmajnem2> hrm
Mar 06 10:03:43 <dmajnem2> the last that I see from it is "Enabling additional executable binary formats binfmt-support"
Mar 06 10:03:54 <dmajnem2> no more output :(
Mar 06 10:04:18 <dmajnem2> could this be because I did not disable the other option?
Mar 06 10:07:20 <ogra> dmajnem2, thats the whole boot process, if you want to see more, remove the quiet from the cmdline
Mar 06 10:08:34 <dmajnem2> ogra: that does not seem to be the case
Mar 06 10:08:42 <dmajnem2> it is booted now as I can see stuff on the HDMI
Mar 06 10:08:50 <dmajnem2> yet, login does not show up on the tty
Mar 06 10:10:26 <dmajnem2> I added "console=ttyS2,115200n8 serialtty=ttyS2" to my boot.scr
Mar 06 10:12:31 <ogra> no, thats off by default
Mar 06 10:12:57 <ogra> you need to create an upstart config for serial login
Mar 06 10:13:32 <dmajnem2> ok, how do I do that?
Mar 06 10:13:48 <ogra> https://help.ubuntu.com/community/SerialConsoleHowto
Mar 06 10:13:51 <dmajnem2> thanks
Mar 06 10:17:06 <dmajnem2> ogra: don't I want ttyS2.conf?
Mar 06 10:21:50 <dmajnem2> or is it ttySO2.conf ?
Mar 06 10:24:05 <dmajnem2> huh, I got a lot more output disabling quite
Mar 06 10:24:07 <dmajnem2> quiet*
Mar 06 10:24:15 <dmajnem2> but it still is "stuck" in the same place
Mar 06 10:25:16 <dmajnem2> yeah, no beans with ttyO2.conf
Mar 06 10:31:31 <dmajnem2> ah, perhaps it should be S2 instead
Mar 06 10:49:35 <dmajnem2> ah, got it working
Mar 06 10:49:37 <dmajnem2> thanks guyts
Mar 06 10:49:39 <dmajnem2> guys*
Mar 06 10:53:37 <pipposantaCROS> anyone with glsl knowledge here?
Mar 06 21:07:34 <Schamus> Hi, can someone help me?
Mar 06 21:08:38 <Schamus> I've installed Ubuntu 10.10 on my Beagleboard (A3) three times. Each time it works for the set up, boots up nicely. When i go to turn it off, i wait for the display to say "no signal" and turn off the beagleboard. Unfortunately, on reboot
Mar 06 21:09:14 <Schamus> the board reaches the "Uncompressing Linux. Booting the kernel..." and then restarts to the beginning Uboot messages
Mar 06 21:09:23 <Schamus> and loops like this indefinitely
Mar 06 21:11:46 <Schamus> Am i supposed to turn off the beagleboard differently?
Mar 06 21:17:50 <Schamus> anyone?
Mar 06 21:33:57 <Schamus> no one? =\
Mar 06 22:45:03 <nacho_> hi guys..maybe my question is crazy and maybe I am wrong and this is not the right channel but maybe u can help me
Mar 06 22:45:15 <nacho_> I own a pocket loox 420 with an arm proccesr v5..is there any possibility to install linux on it
Mar 06 22:47:45 <Schamus> So I'm thinking I might have a problem in that i'm using a microusb for power, instead of the 5v
Mar 06 22:47:56 <Schamus> this may be the reason it won't boot past certain stages.
**** ENDING LOGGING AT Mon Mar 07 02:59:57 2011